20251127给荣品RD-RK3588开发板跑Rockchip的原厂Buildroot【linux-5.10】系统时让AP6275P链接有中文和空格的SSID【特殊字符】
2025/11/27 16:30

缘起：实测网速：80.7 Mbits/sec

经过反复测试，终于把 荣品RD-RK3588开发板 自带的8寸屏的CTP触摸屏调试通了。
Android13的内核linux-5.10
Android13的内核linux-6.1。版本升级之后，

终于把全部的USB接口都点亮USB接口的鼠标了！

当你把荣品RD-RK3588开发板重新适配一把，就相当于从头做了一个项目：【荣品RD-RK3588开发板】。
当然，开发板的功能都是好的，你免除了调试的过程，也就没有解决相关硬件出错的经验/机会了！

结论：荣品的FAE工程师是真的很忙。
代码写的非常写意/潇洒！
【整个DTS，TAB和空格按键都是混用的！^_有些时候看着很难受的！^_】
DTS中的代码排版真的让人看得很难受！

https://doc.rpdzkj.cn/#/zh_cn/%E7%91%9E%E8%8A%AF%E5%BE%AE%E7%B3%BB%E5%88%97/rk3588-rk3588s/7.%E6%8E%A5%E5%8F%A3%E4%BD%BF%E7%94%A8?id=wifi
Buildroot
Buildroot 上使用 wpa_supplicant 进行连接

配置用户名与密码，创建 /tmp/wpa_supplicant.conf 文件，增加如下内容，并修改热点名称和密码

ctrl_interface=DIR=/var/run/wpa_supplicant
    network={
    ssid="rpdzkj-soft1"
    key_mgmt=WPA-PSK
    psk="aaaaaaaa"
}
复制Error已复制
然后杀掉已经存在进程

killall wpa_supplicant
复制Error已复制
重新启动 wpa_supplicant 连接热点

wpa_supplicant -iwlan0 -Dnl80211 -c /tmp/wpa_supplicant.conf -B 
复制Error已复制
获取IP地址

udhcpc -i wlan0
复制Error已复制
连接成功

ifconfig wlan0
复制Error已复制
也可以运行脚本来进行测试

/rp_test/wifi/test_wifi_sta.sh

然后杀掉已经存在进程
killall wpa_supplicant

重新启动 wpa_supplicant 连接热点
wpa_supplicant -iwlan0 -Dnl80211 -c /etc/wpa_supplicant.conf -B 

获取IP地址
udhcpc -i wlan0

连接成功

ifconfig wlan0
复制Error已复制
也可以运行脚本来进行测试

/rp_test/wifi/test_wifi_sta.sh
 

[BEGIN] 2025/11/27 16:43:46
DDR d5483af87d cym 23/11/23-16:15:24,fwver: v1.15
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0x13
CH0 RX Vref:28.5%, TX Vref:23.8%,26.8%
CH1 RX Vref:28.8%, TX Vref:24.8%,25.8%
CH2 RX Vref:29.7%, TX Vref:25.8%,26.8%
CH3 RX Vref:29.3%, TX Vref:24.8%,24.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-ge4e124926e-230922 #lxh (Sep 25 2023 - 10:58:38), fwver: v1.13
unknown raw ID 0 0 0
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 0
spl: mmc init failed with error: -123
Trying to boot from MMC1
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(2e8446f969...) + OK
## Checking uboot 0x00200000 ... sha256(dac27b9ac4...) + OK
## Checking fdt 0x00345490 ... sha256(a434b1c4fe...) + OK
## Checking atf-2 0xff100000 ... sha256(9f75e6ec37...) + OK
## Checking atf-3 0x000f0000 ... sha256(c80587de50...) + OK
## Checking optee 0x08400000 ... sha256(4b2d406bfc...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 90.616/254.675 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-662-g4acbe711b-dirty:finley.xiao, fwver: v1.44
NOTICE:  BL31: Built : 16:44:24, Nov  7 2023
INFO:    spec: 0x1
INFO:    code: 0x88
INFO:    ext 32k is not valid
INFO:    ddr: stride-en 4CH
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO:    l3 cache partition cfg-0
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
I/TC: 
I/TC: OP-TEE version: 3.13.0-752-g62aa10b78 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Mon Sep 25 10:04:34 CST 2023 aarch64, fwver: v1.15 
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9

U-Boot 2017.09 (Nov 27 2025 - 13:44:25 +0800)

Model: Rockchip RK3588 Evaluation Board
MPIDR: 0x81000000
PreSerial: 2, raw, 0xfeb50000
DRAM:  8 GiB
Sysmem: init
Relocation Offset: eda18000
Relocation fdt: eb9fa160 - eb9fecd0
CR: M/C/I
Using default environment

optee api revision: 2.0
mmc@fe2c0000: 1, mmc@fe2e0000: 0
Bootdev(atags): mmc 0
MMC0: HS400 Enhanced Strobe, 200Mhz
PartType: EFI
TEEC: Waring: Could not find security partition
DM: v2
boot mode: loader
RESC: 'boot', blk@0x00019b94
resource: sha256+
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big0_s0 812500 uV
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big1_s0 812500 uV
I2c1 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_npu_s0 812500 uV
spi2: RK806: 2
ON=0x80, OFF=0x00
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_log_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
vdd_ddr_s0 850000 uV
Device 'gpio@fd8a0000': seq 0 is in use by 'gpio@fd8a0000'
serdes_power_init failed to get serdes misc device
get vp0 plane mask:0x5, primary id:2, cursor_plane:-1, from dts
get vp1 plane mask:0xa, primary id:3, cursor_plane:-1, from dts
get vp2 plane mask:0x140, primary id:8, cursor_plane:-1, from dts
get vp3 plane mask:0x280, primary id:9, cursor_plane:-1, from dts
Could not find baseparameter partition
Model: Rockchip RK3588 EVB7 V11 Board
MPIDR: 0x81000000
download key pressed... entering download mode...
RKUSB: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x747c000
/usb device is super-speed
/DDR d5483af87d cym 23/11/23-16:15:24,fwver: v1.15
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0x13
CH0 RX Vref:28.5%, TX Vref:23.8%,25.8%
CH1 RX Vref:28.8%, TX Vref:24.8%,26.8%
CH2 RX Vref:29.3%, TX Vref:25.8%,26.8%
CH3 RX Vref:29.3%, TX Vref:24.8%,24.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-ge4e124926e-230922 #lxh (Sep 25 2023 - 10:58:38), fwver: v1.13
unknown raw ID 0 0 0
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 0
spl: mmc init failed with error: -123
Trying to boot from MMC1
Magic is incorrect.
Error validating A/B metadata from disk. Resetting and writing new A/B metadata to disk.
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(2e8446f969...) + OK
## Checking uboot 0x00200000 ... sha256(ba75dab2a7...) + OK
## Checking fdt 0x00345490 ... sha256(a434b1c4fe...) + OK
## Checking atf-2 0xff100000 ... sha256(9f75e6ec37...) + OK
## Checking atf-3 0x000f0000 ... sha256(c80587de50...) + OK
## Checking optee 0x08400000 ... sha256(4b2d406bfc...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 88.501/250.698 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-662-g4acbe711b-dirty:finley.xiao, fwver: v1.44
NOTICE:  BL31: Built : 16:44:24, Nov  7 2023
INFO:    spec: 0x1
INFO:    code: 0x88
INFO:    ext 32k is not valid
INFO:    ddr: stride-en 4CH
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO:    l3 cache partition cfg-0
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
I/TC: 
I/TC: OP-TEE version: 3.13.0-752-g62aa10b78 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Mon Sep 25 10:04:34 CST 2023 aarch64, fwver: v1.15 
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9

U-Boot 2017.09 (Nov 27 2025 - 16:39:59 +0800)

Model: Rockchip RK3588 Evaluation Board
MPIDR: 0x81000000
PreSerial: 2, raw, 0xfeb50000
DRAM:  8 GiB
Sysmem: init
Relocation Offset: eda18000
Relocation fdt: eb9fa160 - eb9fecd0
CR: M/C/I
Using default environment

optee api revision: 2.0
mmc@fe2c0000: 1, mmc@fe2e0000: 0
Bootdev(atags): mmc 0
MMC0: HS400 Enhanced Strobe, 200Mhz
PartType: EFI
TEEC: Waring: Could not find security partition
DM: v2
boot mode: normal
RESC: 'boot', blk@0x00019b94
resource: sha256+
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big0_s0 812500 uV
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big1_s0 812500 uV
I2c1 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_npu_s0 812500 uV
spi2: RK806: 2
ON=0x80, OFF=0x00
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_log_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
vdd_ddr_s0 850000 uV
Device 'gpio@fd8a0000': seq 0 is in use by 'gpio@fd8a0000'
serdes_power_init failed to get serdes misc device
get vp0 plane mask:0x5, primary id:2, cursor_plane:-1, from dts
get vp1 plane mask:0xa, primary id:3, cursor_plane:-1, from dts
get vp2 plane mask:0x140, primary id:8, cursor_plane:-1, from dts
get vp3 plane mask:0x280, primary id:9, cursor_plane:-1, from dts
Could not find baseparameter partition
Model: Rockchip RK3588 EVB7 V11 Board
MPIDR: 0x81000000
Minidump: init...
Rockchip UBOOT DRM driver version: v1.0.1
vp0 have layer nr:2[0 2 ], primary plane: 2
vp1 have layer nr:2[1 3 ], primary plane: 3
vp2 have layer nr:2[6 8 ], primary plane: 8
vp3 have layer nr:2[7 9 ], primary plane: 9
Using display timing dts
dsi@fde20000:  detailed mode clock 148000 kHz, flags[a]
    H: 1200 1280 1290 1350
    V: 1920 1936 1938 1963
bus_format: 100e
VOP update mode to: 1200x1920p56, type: MIPI0 for VP3
VP3 set crtc_clock to 136364KHz
VOP VP3 enable Esmart3[654x270->654x270@273x825] fmt[2] addr[0xedf04000]
final DSI-Link bandwidth: 909093 Kbps x 4
hdmi@fde80000 disconnected
hdmi@fdea0000 disconnected
CLK: (sync kernel. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
  b0pll 24000 KHz
  b1pll 24000 KHz
  lpll 24000 KHz
  v0pll 24000 KHz
  aupll 786431 KHz
  cpll 1500000 KHz
  gpll 1188000 KHz
  npll 850000 KHz
  ppll 1100000 KHz
  aclk_center_root 702000 KHz
  pclk_center_root 100000 KHz
  hclk_center_root 396000 KHz
  aclk_center_low_root 500000 KHz
  aclk_top_root 750000 KHz
  pclk_top_root 100000 KHz
  aclk_low_top_root 396000 KHz
Net:   Device 'gpio@fec40000': seq 3 is in use by 'gpio@fd8a0000'
eth1: ethernet@fe1c0000
Hit key to stop autoboot('CTRL+C'):  0 
ANDROID: reboot reason: "(none)"
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
## Booting FIT Image at 0xe9486940 with size 0x02372800
Fdt Ramdisk skip relocation
## Loading kernel from FIT Image at e9486940 ...
   Using 'conf' configuration
## Verified-boot: 0
   Trying 'kernel' kernel subimage
     Description:  unavailable
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0xe94cc740
     Data Size:    36882944 Bytes = 35.2 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x00400000
     Entry Point:  0x00400000
     Hash algo:    sha256
     Hash value:   fd2795476afac99fd34c0ac1d729b5549beac81b4dbfbe5157d4525fd3e07c53
   Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at e9486940 ...
   Using 'conf' configuration
   Trying 'fdt' fdt subimage
     Description:  unavailable
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0xe9487140
     Data Size:    283957 Bytes = 277.3 KiB
     Architecture: AArch64
     Load Address: 0x08300000
     Hash algo:    sha256
     Hash value:   b06750c8a13fdd5d83106ab06af8917aca77189aa3bc78185be3c41bf84ff9f2
   Verifying Hash Integrity ... sha256+ OK
   Loading fdt from 0x08300000 to 0x08300000
   Booting using the fdt blob at 0x08300000
   Loading Kernel Image from 0xe94cc740 to 0x00400000 ... OK
   kernel loaded at 0x00400000, end = 0x0272ca00
   Using Device Tree in place at 0000000008300000, end 0000000008348534
WARNING: could not set reg FDT_ERR_BADOFFSET.
## reserved-memory:
  cma: addr=10000000 size=8000000
  drm-logo@00000000: addr=edf00000 size=b8000
  ramoops@110000: addr=110000 size=e0000
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Adding bank: 0x2f0000000 - 0x300000000 (size: 0x10000000)
Total: 778.870/1116.258 ms

Starting kernel ...

[    1.121215] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    1.121233] Linux version 5.10.198 (jinhualong@jinhualong-LEGION-REN7000K-26IRX) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #2 SMP Thu Nov 27 13:44:36 CST 2025
[    1.124834] random: crng init done
[    1.132888] Machine model: Rockchip RK3588 EVB7 V11 Board
[    1.169631] earlycon: uart8250 at MMIO32 0x00000000feb50000 (options '')
[    1.174265] printk: bootconsole [uart8250] enabled
[    1.177082] efi: UEFI not found.
[    1.183096] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@00000000': base 0x0000000000000000, size 0 MiB
[    1.184255] Reserved memory: created CMA memory pool at 0x0000000010000000, size 128 MiB
[    1.184994] OF: reserved mem: initialized node cma, compatible id shared-dma-pool
[    1.306287] Zone ranges:
[    1.306528]   DMA      [mem 0x0000000000200000-0x00000000ffffffff]
[    1.307099]   DMA32    empty
[    1.307366]   Normal   [mem 0x0000000100000000-0x00000002ffffffff]
[    1.307933] Movable zone start for each node
[    1.308324] Early memory node ranges
[    1.308653]   node   0: [mem 0x0000000000200000-0x00000000083fffff]
[    1.309228]   node   0: [mem 0x0000000009400000-0x00000000efffffff]
[    1.309803]   node   0: [mem 0x0000000100000000-0x00000001ffffffff]
[    1.310378]   node   0: [mem 0x00000002f0000000-0x00000002ffffffff]
[    1.310953] Initmem setup node 0 [mem 0x0000000000200000-0x00000002ffffffff]
[    1.359343] psci: probing for conduit method from DT.
[    1.359813] psci: PSCIv1.1 detected in firmware.
[    1.360236] psci: Using standard PSCI v0.2 function IDs
[    1.360717] psci: Trusted OS migration not required
[    1.361167] psci: SMC Calling Convention v1.2
[    1.361924] percpu: Embedded 30 pages/cpu s83800 r8192 d30888 u122880
[    1.362686] Detected VIPT I-cache on CPU0
[    1.363087] CPU features: detected: GIC system register CPU interface
[    1.363677] CPU features: detected: Virtualization Host Extensions
[    1.364246] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    1.364897] alternatives: patching kernel code
[    1.366850] Built 1 zonelists, mobility grouping on.  Total pages: 2059848
[    1.367484] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal  androidboot.verifiedbootstate=orange rw rootwait earlycon=uart8250,mmio32,0xfeb50000 console=ttyFIQ0 irqchip.gicv3_pseudo_nmi=0 root=PARTUUID=614e0000-0000 rcupdate.rcu_expedited=1 rcu_nocbs=all androidboot.fwver=ddr-v1.15-d5483af87d,spl-v1.13,bl31-v1.44,bl32-v1.15,uboot-11/27/2025
[    1.371555] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    1.372671] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    1.373389] mem auto-init: stack:off, heap alloc:off, heap free:off
[    1.380168] software IO TLB: mapped [mem 0x00000000e9f00000-0x00000000edf00000] (64MB)
[    1.439292] Memory: 7973508K/8370176K available (18752K kernel code, 3506K rwdata, 6904K rodata, 6720K init, 590K bss, 265596K reserved, 131072K cma-reserved)
[    1.440692] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    1.441315] ftrace: allocating 57329 entries in 224 pages
[    1.512944] ftrace: allocated 224 pages with 3 groups
[    1.513623] rcu: Hierarchical RCU implementation.
[    1.514058] rcu:     RCU event tracing is enabled.
[    1.514473] rcu:     RCU dyntick-idle grace-period acceleration is enabled.
[    1.515086]     All grace periods are expedited (rcu_expedited).
[    1.515611]     Rude variant of Tasks RCU enabled.
[    1.516027] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    1.520497] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    1.523521] GICv3: GIC: Using split EOI/Deactivate mode
[    1.524003] GICv3: 480 SPIs implemented
[    1.524355] GICv3: 0 Extended SPIs implemented
[    1.524783] GICv3: Distributor has no Range Selector support
[    1.525307] GICv3: 16 PPIs implemented
[    1.525691] GICv3: CPU0: found redistributor 0 region 0:0x00000000fe680000
[    1.526405] ITS [mem 0xfe640000-0xfe65ffff]
[    1.526834] ITS@0x00000000fe640000: allocated 8192 Devices @1001e0000 (indirect, esz 8, psz 64K, shr 0)
[    1.527715] ITS@0x00000000fe640000: allocated 32768 Interrupt Collections @1001f0000 (flat, esz 2, psz 64K, shr 0)
[    1.528664] ITS: using cache flushing for cmd queue
[    1.529135] ITS [mem 0xfe660000-0xfe67ffff]
[    1.529557] ITS@0x00000000fe660000: allocated 8192 Devices @100210000 (indirect, esz 8, psz 64K, shr 0)
[    1.530434] ITS@0x00000000fe660000: allocated 32768 Interrupt Collections @100220000 (flat, esz 2, psz 64K, shr 0)
[    1.531382] ITS: using cache flushing for cmd queue
[    1.532039] GICv3: using LPI property table @0x0000000100230000
[    1.532695] GIC: using cache flushing for LPI property table
[    1.533218] GICv3: CPU0: using allocated LPI pending table @0x0000000100240000
[    1.533919] rcu:     Offload RCU callbacks from CPUs: 0-7.
[    1.643765] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    1.644314] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    1.645274] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    1.647186] Console: colour dummy device 80x25
[    1.647610] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    1.648521] pid_max: default: 32768 minimum: 301
[    1.649040] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    1.649731] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    1.651610] rcu: Hierarchical SRCU implementation.
[    1.652759] Platform MSI: msi-controller@fe640000 domain created
[    1.653303] Platform MSI: msi-controller@fe660000 domain created
[    1.654182] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe640000 domain created
[    1.654927] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe660000 domain created
[    1.655840] EFI services will not be available.
[    1.656472] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
I/TC: Secondary CPU 4 initializing
I/TC: Secondary CPU 4 switching to normal world boot
I/TC: Secondary CPU 5 initializing
I/TC: Secondary CPU 5 switching to normal world boot
I/TC: Secondary CPU 6 initializing
I/TC: Secondary CPU 6 switching to normal world boot
I/TC: Secondary CPU 7 initializing
I/TC: Secondary CPU 7 switching to normal world boot
[    1.658002] Detected VIPT I-cache on CPU1
[    1.658024] GICv3: CPU1: found redistributor 100 region 0:0x00000000fe6a0000
[    1.658039] GICv3: CPU1: using allocated LPI pending table @0x0000000100250000
[    1.658077] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[    1.659226] Detected VIPT I-cache on CPU2
[    1.659245] GICv3: CPU2: found redistributor 200 region 0:0x00000000fe6c0000
[    1.659259] GICv3: CPU2: using allocated LPI pending table @0x0000000100260000
[    1.659293] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[    1.660428] Detected VIPT I-cache on CPU3
[    1.660445] GICv3: CPU3: found redistributor 300 region 0:0x00000000fe6e0000
[    1.660458] GICv3: CPU3: using allocated LPI pending table @0x0000000100270000
[    1.660490] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[    1.661647] CPU features: detected: Spectre-v4
[    1.661649] CPU features: detected: Spectre-BHB
[    1.661651] Detected PIPT I-cache on CPU4
[    1.661661] GICv3: CPU4: found redistributor 400 region 0:0x00000000fe700000
[    1.661669] GICv3: CPU4: using allocated LPI pending table @0x0000000100280000
[    1.661691] CPU4: Booted secondary processor 0x0000000400 [0x414fd0b0]
[    1.662789] Detected PIPT I-cache on CPU5
[    1.662800] GICv3: CPU5: found redistributor 500 region 0:0x00000000fe720000
[    1.662809] GICv3: CPU5: using allocated LPI pending table @0x0000000100290000
[    1.662831] CPU5: Booted secondary processor 0x0000000500 [0x414fd0b0]
[    1.663914] Detected PIPT I-cache on CPU6
[    1.663925] GICv3: CPU6: found redistributor 600 region 0:0x00000000fe740000
[    1.663933] GICv3: CPU6: using allocated LPI pending table @0x00000001002a0000
[    1.663955] CPU6: Booted secondary processor 0x0000000600 [0x414fd0b0]
[    1.665052] Detected PIPT I-cache on CPU7
[    1.665064] GICv3: CPU7: found redistributor 700 region 0:0x00000000fe760000
[    1.665071] GICv3: CPU7: using allocated LPI pending table @0x00000001002b0000
[    1.665093] CPU7: Booted secondary processor 0x0000000700 [0x414fd0b0]
[    1.665142] smp: Brought up 1 node, 8 CPUs
[    1.681685] SMP: Total of 8 processors activated.
[    1.682111] CPU features: detected: Privileged Access Never
[    1.682605] CPU features: detected: LSE atomic instructions
[    1.683101] CPU features: detected: User Access Override
[    1.683576] CPU features: detected: 32-bit EL0 Support
[    1.684034] CPU features: detected: Common not Private translations
[    1.684590] CPU features: detected: RAS Extension Support
[    1.685070] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    1.685836] CPU features: detected: CRC32 instructions
[    1.686293] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    1.686914] CPU features: detected: RCpc load-acquire (LDAPR)
[    1.711900] CPU: All CPU(s) started at EL2
[    1.713972] devtmpfs: initialized
[    1.724108] Registered cp15_barrier emulation handler
[    1.724565] Registered setend emulation handler
[    1.725025] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    1.725897] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    1.727473] pinctrl core: initialized pinctrl subsystem
[    1.728105] DMI not present or invalid.
[    1.728533] NET: Registered protocol family 16
[    1.729484] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[    1.730197] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    1.731281] Registered FIQ tty driver
[    1.731700] thermal_sys: Registered thermal governor 'fair_share'
[    1.731701] thermal_sys: Registered thermal governor 'step_wise'
[    1.732243] thermal_sys: Registered thermal governor 'user_space'
[    1.732783] thermal_sys: Registered thermal governor 'power_allocator'
[    1.733437] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    1.734753] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[    1.735489] thermal thermal_zone3: power_allocator: sustainable_power will be estimated
[    1.736221] thermal thermal_zone4: power_allocator: sustainable_power will be estimated
[    1.736950] thermal thermal_zone5: power_allocator: sustainable_power will be estimated
[    1.737677] thermal thermal_zone6: power_allocator: sustainable_power will be estimated
[    1.738401] cpuidle: using governor menu
[    1.738829] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    1.739514] ASID allocator initialised with 65536 entries
[    1.741188] ramoops: dmesg-0    0x18000@0x0000000000110000
[    1.741654] ramoops: dmesg-1    0x18000@0x0000000000128000
[    1.742384] ramoops: console    0x80000@0x0000000000140000
[    1.742856] ramoops: pmsg    0x30000@0x00000000001c0000
[    1.743516] printk: console [ramoops-1] enabled
[    1.743918] pstore: Registered ramoops as persistent store backend
[    1.744470] ramoops: using 0xe0000@0x110000, ecc: 0
[    1.778004] rockchip-gpio fd8a0000.gpio: probed /pinctrl/gpio@fd8a0000
[    1.778727] rockchip-gpio fec20000.gpio: probed /pinctrl/gpio@fec20000
[    1.779425] rockchip-gpio fec30000.gpio: probed /pinctrl/gpio@fec30000
[    1.780151] rockchip-gpio fec40000.gpio: probed /pinctrl/gpio@fec40000
[    1.780904] rockchip-gpio fec50000.gpio: probed /pinctrl/gpio@fec50000
[    1.781517] rockchip-pinctrl pinctrl: probed pinctrl
[    1.792088] fiq_debugger fiq_debugger.0: IRQ fiq not found
[    1.792584] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[    1.793099] fiq_debugger_probe: could not install nmi irq handler
[[    1.793683] printk: console [ttyFIQ0] enabled
    1.793683] printk: console [ttyFIQ0] enabled
[    1.794449] printk: bootconsole [uart8250] disabled
[    1.794449] printk: bootconsole [uart8250] disabled
[    1.794926] Registered fiq debugger ttyFIQ0
[    1.795134] vcc5v0_sys: supplied by vcc12v_dcin
[    1.795209] vcc5v0_usbdcin: supplied by vcc12v_dcin
[    1.795331] vcc5v0_usb: supplied by vcc5v0_usbdcin
[    1.795408] vcc_1v1_nldo_s3: supplied by vcc5v0_sys
[    1.795566] vbus5v0_typec: supplied by vcc5v0_usb
[    1.795663] vcc3v3_pcie30: supplied by vcc12v_dcin
[    1.795738] vcc5v0_host: supplied by vcc5v0_usb
[    1.796132] iommu: Default domain type: Translated 
[    1.798453] SCSI subsystem initialized
[    1.798506] usbcore: registered new interface driver usbfs
[    1.798517] usbcore: registered new interface driver hub
[    1.798528] usbcore: registered new device driver usb
[    1.798552] mc: Linux media interface: v0.10
[    1.798559] videodev: Linux video capture interface: v2.00
[    1.798578] pps_core: LinuxPPS API ver. 1 registered
[    1.798581] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.798587] PTP clock support registered
[    1.798601] EDAC MC: Ver: 3.0.0
[    1.798827] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[    1.798854] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[    1.799647] Advanced Linux Sound Architecture Driver Initialized.
[    1.799775] Bluetooth: Core ver 2.22
[    1.799783] NET: Registered protocol family 31
[    1.799786] Bluetooth: HCI device and connection manager initialized
[    1.799790] Bluetooth: HCI socket layer initialized
[    1.799793] Bluetooth: L2CAP socket layer initialized
[    1.799799] Bluetooth: SCO socket layer initialized
[    1.801026] rockchip-cpuinfo cpuinfo: SoC        : 35881000
[    1.801030] rockchip-cpuinfo cpuinfo: Serial        : 7f4af88b63ded61f
[    1.801230] clocksource: Switched to clocksource arch_sys_counter
[    2.043150] NET: Registered protocol family 2
[    2.043250] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    2.045184] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    2.045253] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    2.045580] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[    2.046219] TCP: Hash tables configured (established 65536 bind 65536)
[    2.046252] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    2.046371] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    2.046526] NET: Registered protocol family 1
[    2.046733] RPC: Registered named UNIX socket transport module.
[    2.046737] RPC: Registered udp transport module.
[    2.046740] RPC: Registered tcp transport module.
[    2.046742] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    2.047043] PCI: CLS 0 bytes, default 64
[    2.047646] rockchip-thermal fec00000.tsadc: Missing rockchip,grf property
[    2.048090] rockchip-thermal fec00000.tsadc: tsadc is probed successfully!
[    2.048632] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    2.050614] Initialise system trusted keyrings
[    2.050679] workingset: timestamp_bits=62 max_order=21 bucket_order=0
[    2.051906] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.052087] NFS: Registering the id_resolver key type
[    2.052094] Key type id_resolver registered
[    2.052097] Key type id_legacy registered
[    2.052109] ntfs: driver 2.1.32 [Flags: R/O].
[    2.052160] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    2.052237] fuse: init (API version 7.32)
[    2.052310] SGI XFS with security attributes, no debug enabled
[    2.072776] NET: Registered protocol family 38
[    2.072783] Key type asymmetric registered
[    2.072786] Asymmetric key parser 'x509' registered
[    2.072797] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[    2.072800] io scheduler mq-deadline registered
[    2.072803] io scheduler kyber registered
[    2.073142] rockchip-csi2-dphy-hw fedc0000.csi2-dphy0-hw: csi2 dphy hw probe successfully!
[    2.073196] rockchip-csi2-dphy-hw fedc8000.csi2-dphy1-hw: csi2 dphy hw probe successfully!
[    2.079262] rockchip-hdptx-phy-hdmi fed60000.hdmiphy: hdptx phy init success
[    2.079811] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx phy init success
[    2.081520] rk-pcie fe190000.pcie: invalid prsnt-gpios property in node
[    2.081740] rk-pcie fe170000.pcie: invalid prsnt-gpios property in node
[    2.081794] pwm-backlight backlight: supply power not found, using dummy regulator
[    2.081985] iep: Module initialized.
[    2.082007] mpp_service mpp-srv: unknown mpp version for missing VCS info
[    2.082010] mpp_service mpp-srv: probe start
[    2.082711] mpp_vdpu1 fdb51000.avsd-plus: Adding to iommu group 1
[    2.082875] mpp_vdpu1 fdb51000.avsd-plus: probe device
[    2.082949] mpp_vdpu1 fdb51000.avsd-plus: reset_group->rw_sem_on=0
[    2.082954] mpp_vdpu1 fdb51000.avsd-plus: reset_group->rw_sem_on=0
[    2.083027] mpp_vdpu1 fdb51000.avsd-plus: probing finish
[    2.083252] mpp_vdpu2 fdb50400.vdpu: Adding to iommu group 1
[    2.083281] mpp_vdpu2 fdb50400.vdpu: probe device
[    2.083339] mpp_vdpu2 fdb50400.vdpu: reset_group->rw_sem_on=0
[    2.083343] mpp_vdpu2 fdb50400.vdpu: reset_group->rw_sem_on=0
[    2.083411] mpp_vdpu2 fdb50400.vdpu: probing finish
[    2.083519] mpp_vepu2 jpege-ccu: probing start
[    2.083523] mpp_vepu2 jpege-ccu: probing finish
[    2.083595] mpp_vepu2 fdb50000.vepu: Adding to iommu group 1
[    2.083624] mpp_vepu2 fdb50000.vepu: probing start
[    2.083676] mpp_vepu2 fdb50000.vepu: reset_group->rw_sem_on=0
[    2.083679] mpp_vepu2 fdb50000.vepu: reset_group->rw_sem_on=0
[    2.083736] mpp_vepu2 fdb50000.vepu: probing finish
[    2.083789] mpp_vepu2 fdba0000.jpege-core: Adding to iommu group 5
[    2.083854] mpp_vepu2 fdba0000.jpege-core: probing start
[    2.083929] mpp_vepu2 fdba0000.jpege-core: attach ccu success
[    2.083983] mpp_vepu2 fdba0000.jpege-core: probing finish
[    2.084020] mpp_vepu2 fdba4000.jpege-core: Adding to iommu group 6
[    2.084087] mpp_vepu2 fdba4000.jpege-core: probing start
[    2.084151] mpp_vepu2 fdba4000.jpege-core: attach ccu success
[    2.084203] mpp_vepu2 fdba4000.jpege-core: probing finish
[    2.084247] mpp_vepu2 fdba8000.jpege-core: Adding to iommu group 7
[    2.084306] mpp_vepu2 fdba8000.jpege-core: probing start
[    2.084368] mpp_vepu2 fdba8000.jpege-core: attach ccu success
[    2.084419] mpp_vepu2 fdba8000.jpege-core: probing finish
[    2.084464] mpp_vepu2 fdbac000.jpege-core: Adding to iommu group 8
[    2.084525] mpp_vepu2 fdbac000.jpege-core: probing start
[    2.084594] mpp_vepu2 fdbac000.jpege-core: attach ccu success
[    2.084648] mpp_vepu2 fdbac000.jpege-core: probing finish
[    2.084820] mpp-iep2 fdbb0000.iep: Adding to iommu group 9
[    2.084882] mpp-iep2 fdbb0000.iep: probe device
[    2.084963] mpp-iep2 fdbb0000.iep: allocate roi buffer failed
[    2.085016] mpp-iep2 fdbb0000.iep: probing finish
[    2.085142] mpp_jpgdec fdb90000.jpegd: Adding to iommu group 4
[    2.085259] mpp_jpgdec fdb90000.jpegd: probe device
[    2.085381] mpp_jpgdec fdb90000.jpegd: probing finish
[    2.085631] mpp_rkvdec2 fdc30000.rkvdec-ccu: rkvdec-ccu, probing start
[    2.085672] mpp_rkvdec2 fdc30000.rkvdec-ccu: ccu-mode: 1
[    2.085675] mpp_rkvdec2 fdc30000.rkvdec-ccu: probing finish
[    2.085741] mpp_rkvdec2 fdc38100.rkvdec-core: Adding to iommu group 12
[    2.085916] mpp_rkvdec2 fdc38100.rkvdec-core: rkvdec-core, probing start
[    2.085993] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_a is not found!
[    2.085997] rkvdec2_init:1022: No niu aclk reset resource define
[    2.086000] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_h is not found!
[    2.086003] rkvdec2_init:1025: No niu hclk reset resource define
[    2.086016] mpp_rkvdec2 fdc38100.rkvdec-core: no regulator, devfreq is disabled
[    2.086059] mpp_rkvdec2 fdc38100.rkvdec-core: core_mask=00010001
[    2.086063] mpp_rkvdec2 fdc38100.rkvdec-core: attach ccu as core 0
[    2.086193] mpp_rkvdec2 fdc38100.rkvdec-core: sram_start 0x00000000ff001000
[    2.086197] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_iova 0x00000000fff00000
[    2.086200] mpp_rkvdec2 fdc38100.rkvdec-core: sram_size 491520
[    2.086203] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_size 1048576
[    2.086206] mpp_rkvdec2 fdc38100.rkvdec-core: min_width 512
[    2.086210] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_info_count 20
[    2.086213] mpp_rkvdec2 fdc38100.rkvdec-core: [136, 24576]
[    2.086216] mpp_rkvdec2 fdc38100.rkvdec-core: [137, 49152]
[    2.086219] mpp_rkvdec2 fdc38100.rkvdec-core: [141, 90112]
[    2.086222] mpp_rkvdec2 fdc38100.rkvdec-core: [140, 49152]
[    2.086225] mpp_rkvdec2 fdc38100.rkvdec-core: [139, 180224]
[    2.086228] mpp_rkvdec2 fdc38100.rkvdec-core: [133, 49152]
[    2.086231] mpp_rkvdec2 fdc38100.rkvdec-core: [134, 8192]
[    2.086234] mpp_rkvdec2 fdc38100.rkvdec-core: [135, 4352]
[    2.086237] mpp_rkvdec2 fdc38100.rkvdec-core: [138, 13056]
[    2.086240] mpp_rkvdec2 fdc38100.rkvdec-core: [142, 291584]
[    2.086260] mpp_rkvdec2 fdc38100.rkvdec-core: probing finish
[    2.086312] mpp_rkvdec2 fdc48100.rkvdec-core: Adding to iommu group 13
[    2.086470] mpp_rkvdec2 fdc48100.rkvdec-core: rkvdec-core, probing start
[    2.086543] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_a is not found!
[    2.086547] rkvdec2_init:1022: No niu aclk reset resource define
[    2.086550] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_h is not found!
[    2.086553] rkvdec2_init:1025: No niu hclk reset resource define
[    2.086566] mpp_rkvdec2 fdc48100.rkvdec-core: no regulator, devfreq is disabled
[    2.086596] mpp_rkvdec2 fdc48100.rkvdec-core: core_mask=00020002
[    2.086611] mpp_rkvdec2 fdc48100.rkvdec-core: attach ccu as core 1
[    2.086760] mpp_rkvdec2 fdc48100.rkvdec-core: sram_start 0x00000000ff079000
[    2.086763] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_iova 0x00000000ffe00000
[    2.086766] mpp_rkvdec2 fdc48100.rkvdec-core: sram_size 487424
[    2.086769] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_size 1048576
[    2.086772] mpp_rkvdec2 fdc48100.rkvdec-core: min_width 512
[    2.086776] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_info_count 20
[    2.086779] mpp_rkvdec2 fdc48100.rkvdec-core: [136, 24576]
[    2.086782] mpp_rkvdec2 fdc48100.rkvdec-core: [137, 49152]
[    2.086785] mpp_rkvdec2 fdc48100.rkvdec-core: [141, 90112]
[    2.086788] mpp_rkvdec2 fdc48100.rkvdec-core: [140, 49152]
[    2.086791] mpp_rkvdec2 fdc48100.rkvdec-core: [139, 180224]
[    2.086794] mpp_rkvdec2 fdc48100.rkvdec-core: [133, 49152]
[    2.086797] mpp_rkvdec2 fdc48100.rkvdec-core: [134, 8192]
[    2.086799] mpp_rkvdec2 fdc48100.rkvdec-core: [135, 4352]
[    2.086802] mpp_rkvdec2 fdc48100.rkvdec-core: [138, 13056]
[    2.086805] mpp_rkvdec2 fdc48100.rkvdec-core: [142, 291584]
[    2.086824] mpp_rkvdec2 fdc48100.rkvdec-core: probing finish
[    2.087015] mpp_rkvenc2 rkvenc-ccu: probing start
[    2.087019] mpp_rkvenc2 rkvenc-ccu: probing finish
[    2.087160] rk-pcie fe190000.pcie: IRQ msi not found
[    2.087171] rk-pcie fe190000.pcie: use outband MSI support
[    2.087179] rk-pcie fe190000.pcie: Missing *config* reg space
[    2.087200] rk-pcie fe190000.pcie: host bridge /pcie@fe190000 ranges:
[    2.087238] rk-pcie fe190000.pcie:      err 0x00f4000000..0x00f40fffff -> 0x00f4000000
[    2.087255] rk-pcie fe190000.pcie:       IO 0x00f4100000..0x00f41fffff -> 0x00f4100000
[    2.087275] rk-pcie fe190000.pcie:      MEM 0x00f4200000..0x00f4ffffff -> 0x00f4200000
[    2.087287] rk-pcie fe170000.pcie: IRQ msi not found
[    2.087291] rk-pcie fe190000.pcie:      MEM 0x0a00000000..0x0a3fffffff -> 0x0a00000000
[    2.087305] rk-pcie fe170000.pcie: use outband MSI support
[    2.087312] rk-pcie fe170000.pcie: Missing *config* reg space
[    2.087318] rk-pcie fe190000.pcie: Missing *config* reg space
[    2.087330] rk-pcie fe170000.pcie: host bridge /pcie@fe170000 ranges:
[    2.087348] rk-pcie fe190000.pcie: invalid resource
[    2.087352] rk-pcie fe170000.pcie:      err 0x00f2000000..0x00f20fffff -> 0x00f2000000
[    2.087364] rk-pcie fe170000.pcie:       IO 0x00f2100000..0x00f21fffff -> 0x00f2100000
[    2.087379] rk-pcie fe170000.pcie:      MEM 0x00f2200000..0x00f2ffffff -> 0x00f2200000
[    2.087390] rk-pcie fe170000.pcie:      MEM 0x0980000000..0x09bfffffff -> 0x0980000000
[    2.087415] rk-pcie fe170000.pcie: Missing *config* reg space
[    2.087443] rk-pcie fe170000.pcie: invalid resource
[    2.087499] mpp_av1dec: Adding child /av1d@fdc70000
[    2.087659] mpp_av1dec: register device av1d-master
[    2.087671] mpp_av1dec av1d-master: av1_iommu_of_xlate,784
[    2.087683] av1_iommu_probe_device,736, consumer : av1d-master, supplier : fdca0000.iommu
[    2.087689] mpp_av1dec av1d-master: Adding to iommu group 17
[    2.087843] mpp_av1dec av1d-master: probing start
[    2.087994] mpp_av1dec av1d-master: probing finish
[    2.088013] mpp_service mpp-srv: probe success
[    2.095030] dma-pl330 fea10000.dma-controller: Loaded driver for PL330 DMAC-241330
[    2.095037] dma-pl330 fea10000.dma-controller:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    2.095573] dma-pl330 fea30000.dma-controller: Loaded driver for PL330 DMAC-241330
[    2.095578] dma-pl330 fea30000.dma-controller:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    2.096127] dma-pl330 fed10000.dma-controller: Loaded driver for PL330 DMAC-241330
[    2.096132] dma-pl330 fed10000.dma-controller:     DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    2.096573] rockchip-pvtm fda40000.pvtm: pvtm@0 probed
[    2.096613] rockchip-pvtm fda50000.pvtm: pvtm@1 probed
[    2.096646] rockchip-pvtm fda60000.pvtm: pvtm@2 probed
[    2.096678] rockchip-pvtm fdaf0000.pvtm: pvtm@3 probed
[    2.096709] rockchip-pvtm fdb30000.pvtm: pvtm@4 probed
[    2.097087] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[    2.097639] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    2.097997] febc0000.serial: ttyS9 at MMIO 0xfebc0000 (irq = 107, base_baud = 1500000) is a 16550A
[    2.099421] rockchip-vop2 fdd90000.vop: Adding to iommu group 16
[    2.106045] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2
[    2.106053] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3
[    2.106059] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8
[    2.106065] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9
[    2.106230] [drm] failed to init overlay plane Cluster0-win1
[    2.106254] [drm] failed to init overlay plane Cluster1-win1
[    2.106276] [drm] failed to init overlay plane Cluster2-win1
[    2.106298] [drm] failed to init overlay plane Cluster3-win1
[    2.113993] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffffffc00935e230)
[    2.114327] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[    2.114604] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffffffc00936cdc0)
[    2.114970] dwhdmi-rockchip fdea0000.hdmi: registered ddc I2C bus driver
[    2.115237] rockchip-drm display-subsystem: bound fdea0000.hdmi (ops 0xffffffc00936cdc0)
[    2.115272] dw-mipi-dsi2 fde20000.dsi: [drm:dw_mipi_dsi2_bind] *ERROR* Failed to find panel or bridge: -517
[    2.121258] brd: module loaded
[    2.123227] loop: module loaded
[    2.123338] zram: Added device: zram0
[    2.123427] lkdtm: No crash points registered, enable through debugfs
[    2.123717] system_heap: orders[0] = 6
[    2.123721] system_heap: orders[1] = 4
[    2.123724] system_heap: orders[2] = 0
[    2.124393] ahci fe210000.sata: supply ahci not found, using dummy regulator
[    2.124438] ahci fe210000.sata: supply phy not found, using dummy regulator
[    2.124458] naneng-combphy fee00000.phy: phy type select 1 overwriting type 2
[    2.124482] ahci fe210000.sata: supply target not found, using dummy regulator
[    2.124518] ahci fe210000.sata: forcing port_map 0x0 -> 0x1
[    2.124536] ahci fe210000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[    2.124542] ahci fe210000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc apst 
[    2.124550] ahci fe210000.sata: port 0 can do FBS, forcing FBSCP
[    2.124995] scsi host0: ahci
[    2.125083] ata1: SATA max UDMA/133 mmio [mem 0xfe210000-0xfe210fff] port 0x100 irq 94
[    2.125912] rockchip-spi feb20000.spi: no high_speed pinctrl state
[    2.126953] rk806 spi2.0: chip id: RK806,ver:0x2, 0x1
[    2.127077] rk806 spi2.0: ON: 0x80 OFF:0x0
[    2.128497] vdd_gpu_s0: supplied by vcc5v0_sys
[    2.129450] vdd_cpu_lit_s0: supplied by vcc5v0_sys
[    2.130023] vdd_log_s0: supplied by vcc5v0_sys
[    2.130534] vdd_vdenc_s0: supplied by vcc5v0_sys
[    2.131095] vdd_ddr_s0: supplied by vcc5v0_sys
[    2.131412] vdd2_ddr_s3: supplied by vcc5v0_sys
[    2.131904] vdd_2v0_pldo_s3: supplied by vcc5v0_sys
[    2.132342] vcc_3v3_s3: supplied by vcc5v0_sys
[    2.132757] vddq_ddr_s0: supplied by vcc5v0_sys
[    2.133251] vcc_1v8_s3: supplied by vcc5v0_sys
[    2.133696] vdd_0v75_s3: supplied by vcc_1v1_nldo_s3
[    2.134185] vdd_ddr_pll_s0: supplied by vcc_1v1_nldo_s3
[    2.134616] avdd_0v75_s0: supplied by vcc_1v1_nldo_s3
[    2.135046] vdd_0v85_s0: supplied by vcc_1v1_nldo_s3
[    2.135469] vdd_0v75_s0: supplied by vcc_1v1_nldo_s3
[    2.135982] avcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[    2.136533] vcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[    2.137015] avdd_1v2_s0: supplied by vdd_2v0_pldo_s3
[    2.137501] vcc_3v3_s0: supplied by vcc5v0_sys
[    2.137932] vccio_sd_s0: supplied by vcc5v0_sys
[    2.138373] pldo6_s3: supplied by vcc5v0_sys
[    2.138561] rk806 spi2.0: no sleep-setting state
[    2.138565] rk806 spi2.0: no reset-setting pinctrl state
[    2.138569] rk806 spi2.0: no dvs-setting pinctrl state
[    2.139763] rockchip-spi feb20000.spi: probed, poll=0, rsd=0, cs-inactive=0, ready=0
[    2.141002] rk_gmac-dwmac fe1c0000.ethernet: IRQ eth_lpi not found
[    2.141125] rk_gmac-dwmac fe1c0000.ethernet: supply phy not found, using dummy regulator
[    2.141167] rk_gmac-dwmac fe1c0000.ethernet: clock input or output? (input).
[    2.141171] rk_gmac-dwmac fe1c0000.ethernet: TX delay(0x44).
[    2.141175] rk_gmac-dwmac fe1c0000.ethernet: Can not read property: rx_delay.
[    2.141179] rk_gmac-dwmac fe1c0000.ethernet: set rx_delay to 0xffffffff
[    2.141193] rk_gmac-dwmac fe1c0000.ethernet: integrated PHY? (no).
[    2.141198] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_rx
[    2.141202] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_tx
[    2.141212] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock clk_mac_speed
[    2.141216] rk_gmac-dwmac fe1c0000.ethernet: clock input from PHY
[    2.141441] rk_gmac-dwmac fe1c0000.ethernet: init for RGMII_RXID
[    2.141501] rk_gmac-dwmac fe1c0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[    2.141506] rk_gmac-dwmac fe1c0000.ethernet:     DWMAC4/5
[    2.141511] rk_gmac-dwmac fe1c0000.ethernet: DMA HW capability register supported
[    2.141515] rk_gmac-dwmac fe1c0000.ethernet: RX Checksum Offload Engine supported
[    2.141518] rk_gmac-dwmac fe1c0000.ethernet: TX Checksum insertion supported
[    2.141522] rk_gmac-dwmac fe1c0000.ethernet: Wake-Up On Lan supported
[    2.141545] rk_gmac-dwmac fe1c0000.ethernet: TSO supported
[    2.141548] rk_gmac-dwmac fe1c0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.141552] rk_gmac-dwmac fe1c0000.ethernet: Enabled Flow TC (entries=2)
[    2.141556] rk_gmac-dwmac fe1c0000.ethernet: TSO feature enabled
[    2.141560] rk_gmac-dwmac fe1c0000.ethernet: Using 32 bits DMA width
[    2.276018] usbcore: registered new interface driver rtl8150
[    2.276035] usbcore: registered new interface driver r8152
[    2.287607] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.287616] ehci-pci: EHCI PCI platform driver
[    2.287637] ehci-platform: EHCI generic platform driver
[    2.289786] ehci-platform fc800000.usb: EHCI Host Controller
[    2.289840] ehci-platform fc800000.usb: new USB bus registered, assigned bus number 1
[    2.289888] ehci-platform fc800000.usb: irq 20, io mem 0xfc800000
[    2.301232] ehci-platform fc800000.usb: USB 2.0 started, EHCI 1.00
[    2.301292] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.301297] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.301301] usb usb1: Product: EHCI Host Controller
[    2.301305] usb usb1: Manufacturer: Linux 5.10.198 ehci_hcd
[    2.301308] usb usb1: SerialNumber: fc800000.usb
[    2.301448] hub 1-0:1.0: USB hub found
[    2.301458] hub 1-0:1.0: 1 port detected
[    2.303710] ehci-platform fc880000.usb: EHCI Host Controller
[    2.303764] ehci-platform fc880000.usb: new USB bus registered, assigned bus number 2
[    2.303806] ehci-platform fc880000.usb: irq 22, io mem 0xfc880000
[    2.314566] ehci-platform fc880000.usb: USB 2.0 started, EHCI 1.00
[    2.314616] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.314621] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.314624] usb usb2: Product: EHCI Host Controller
[    2.314628] usb usb2: Manufacturer: Linux 5.10.198 ehci_hcd
[    2.314631] usb usb2: SerialNumber: fc880000.usb
[    2.314750] hub 2-0:1.0: USB hub found
[    2.314760] hub 2-0:1.0: 1 port detected
[    2.315020] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.315026] ohci-platform: OHCI generic platform driver
[    2.315130] ohci-platform fc840000.usb: Generic Platform OHCI controller
[    2.315175] ohci-platform fc840000.usb: new USB bus registered, assigned bus number 3
[    2.315208] ohci-platform fc840000.usb: irq 21, io mem 0xfc840000
[    2.347922] rk-pcie fe190000.pcie: PCIe Link up, LTSSM is 0x30011
[    2.347928] rk-pcie fe170000.pcie: PCIe Link up, LTSSM is 0x30011
[    2.348080] rk-pcie fe170000.pcie: PCI host bridge to bus 0002:20
[    2.348087] rk-pcie fe190000.pcie: PCI host bridge to bus 0004:40
[    2.348095] pci_bus 0004:40: root bus resource [bus 40-4f]
[    2.348102] pci_bus 0004:40: root bus resource [??? 0xf4000000-0xf40fffff flags 0x0]
[    2.348110] pci_bus 0004:40: root bus resource [io  0x0000-0xfffff] (bus address [0xf4100000-0xf41fffff])
[    2.348117] pci_bus 0004:40: root bus resource [mem 0xf4200000-0xf4ffffff]
[    2.348124] pci_bus 0004:40: root bus resource [mem 0xa00000000-0xa3fffffff pref]
[    2.348136] pci_bus 0002:20: root bus resource [bus 20-2f]
[    2.348146] pci_bus 0002:20: root bus resource [??? 0xf2000000-0xf20fffff flags 0x0]
[    2.348157] pci_bus 0002:20: root bus resource [io  0x100000-0x1fffff] (bus address [0xf2100000-0xf21fffff])
[    2.348162] pci 0004:40:00.0: [1d87:3588] type 01 class 0x060400
[    2.348176] pci_bus 0002:20: root bus resource [mem 0xf2200000-0xf2ffffff]
[    2.348185] pci 0004:40:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref]
[    2.348190] pci_bus 0002:20: root bus resource [mem 0x980000000-0x9bfffffff pref]
[    2.348224] pci 0002:20:00.0: [1d87:3588] type 01 class 0x060400
[    2.348266] pci 0002:20:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref]
[    2.348285] pci 0004:40:00.0: supports D1 D2
[    2.348295] pci 0004:40:00.0: PME# supported from D0 D1 D3hot
[    2.348341] pci 0002:20:00.0: supports D1 D2
[    2.348350] pci 0002:20:00.0: PME# supported from D0 D1 D3hot
[    2.370701] pci 0002:20:00.0: Primary bus is hard wired to 0
[    2.370720] pci 0002:20:00.0: bridge configuration invalid ([bus 01-ff]), reconfiguring
[    2.370956] pci 0002:21:00.0: [14e4:449d] type 00 class 0x028000
[    2.371057] pci 0002:21:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[    2.371061] pci 0004:40:00.0: Primary bus is hard wired to 0
[    2.371068] pci 0004:40:00.0: bridge configuration invalid ([bus 01-ff]), reconfiguring
[    2.371140] pci 0002:21:00.0: reg 0x18: [mem 0x00000000-0x003fffff 64bit]
[    2.371424] pci 0004:41:00.0: [10ec:8168] type 00 class 0x020000
[    2.371562] pci 0004:41:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[    2.371573] pci 0004:41:00.0: reg 0x10: [io  size 0x0100]
[    2.371743] pci 0004:41:00.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit]
[    2.371853] pci 0004:41:00.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit]
[    2.372152] pci 0002:21:00.0: supports D1 D2
[    2.372162] pci 0002:21:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    2.372605] pci 0004:41:00.0: supports D1 D2
[    2.372615] pci 0004:41:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    2.375291] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    2.375296] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.375299] usb usb3: Product: Generic Platform OHCI controller
[    2.375303] usb usb3: Manufacturer: Linux 5.10.198 ohci_hcd
[    2.375307] usb usb3: SerialNumber: fc840000.usb
[    2.375429] hub 3-0:1.0: USB hub found
[    2.375440] hub 3-0:1.0: 1 port detected
[    2.375609] ohci-platform fc8c0000.usb: Generic Platform OHCI controller
[    2.375655] ohci-platform fc8c0000.usb: new USB bus registered, assigned bus number 4
[    2.375686] ohci-platform fc8c0000.usb: irq 23, io mem 0xfc8c0000
[    2.393507] pci_bus 0002:21: busn_res: [bus 21-2f] end is updated to 21
[    2.393543] pci 0002:20:00.0: BAR 8: assigned [mem 0xf2200000-0xf27fffff]
[    2.393557] pci 0002:20:00.0: BAR 6: assigned [mem 0xf2800000-0xf280ffff pref]
[    2.393571] pci 0002:21:00.0: BAR 2: assigned [mem 0xf2400000-0xf27fffff 64bit]
[    2.393625] pci 0002:21:00.0: BAR 0: assigned [mem 0xf2200000-0xf220ffff 64bit]
[    2.393676] pci 0002:20:00.0: PCI bridge to [bus 21]
[    2.393688] pci 0002:20:00.0:   bridge window [mem 0xf2200000-0xf27fffff]
[    2.403704] pci_bus 0004:41: busn_res: [bus 41-4f] end is updated to 41
[    2.403735] pci 0004:40:00.0: BAR 8: assigned [mem 0xf4200000-0xf42fffff]
[    2.403748] pci 0004:40:00.0: BAR 6: assigned [mem 0xf4300000-0xf430ffff pref]
[    2.403759] pci 0004:40:00.0: BAR 7: assigned [io  0x1000-0x1fff]
[    2.403772] pci 0004:41:00.0: BAR 4: assigned [mem 0xf4200000-0xf4203fff 64bit]
[    2.403826] pci 0004:41:00.0: BAR 2: assigned [mem 0xf4204000-0xf4204fff 64bit]
[    2.403877] pci 0004:41:00.0: BAR 0: assigned [io  0x1000-0x10ff]
[    2.403898] pci 0004:40:00.0: PCI bridge to [bus 41]
[    2.403908] pci 0004:40:00.0:   bridge window [io  0x1000-0x1fff]
[    2.403919] pci 0004:40:00.0:   bridge window [mem 0xf4200000-0xf42fffff]
[    2.406840] pcieport 0002:20:00.0: PME: Signaling with IRQ 156
[    2.407054] pcieport 0004:40:00.0: PME: Signaling with IRQ 165
[    2.407262] r8168 Gigabit Ethernet driver 8.049.02-NAPI loaded
[    2.407314] r8168 0004:41:00.0: enabling device (0000 -> 0003)
[    2.423596] r8168 0004:41:00.0 (unnamed net_device) (uninitialized): Invalid ether addr 00:00:00:00:00:00
[    2.423615] r8168 0004:41:00.0 (unnamed net_device) (uninitialized): Random ether addr 8a:c4:fe:a1:05:82
[    2.424061] r8168: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625.
[    2.426148] r8168  Copyright (C) 2021 Realtek NIC software team <nicfae@realtek.com> 
[    2.426148]  This program comes with ABSOLUTELY NO WARRANTY; for details, please see <http://www.gnu.org/licenses/>. 
[    2.426148]  This is free software, and you are welcome to redistribute it under certain conditions; see <http://www.gnu.org/licenses/>. 
[    2.435286] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    2.435292] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.435295] usb usb4: Product: Generic Platform OHCI controller
[    2.435299] usb usb4: Manufacturer: Linux 5.10.198 ohci_hcd
[    2.435303] usb usb4: SerialNumber: fc8c0000.usb
[    2.435419] hub 4-0:1.0: USB hub found
[    2.435429] hub 4-0:1.0: 1 port detected
[    2.435856] phy phy-fd5d4000.syscon:usb2-phy@4000.3: illegal mode
[    2.435863] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[    2.435914] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 5
[    2.435988] xhci-hcd xhci-hcd.5.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000800002010010
[    2.436006] xhci-hcd xhci-hcd.5.auto: irq 146, io mem 0xfc400000
[    2.436061] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[    2.436101] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 6
[    2.436107] xhci-hcd xhci-hcd.5.auto: Host supports USB 3.0 SuperSpeed
[    2.436142] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.436147] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.436151] usb usb5: Product: xHCI Host Controller
[    2.436154] usb usb5: Manufacturer: Linux 5.10.198 xhci-hcd
[    2.436158] usb usb5: SerialNumber: xhci-hcd.5.auto
[    2.436275] hub 5-0:1.0: USB hub found
[    2.436286] hub 5-0:1.0: 1 port detected
[    2.436380] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.436407] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[    2.436411] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.436415] usb usb6: Product: xHCI Host Controller
[    2.436418] usb usb6: Manufacturer: Linux 5.10.198 xhci-hcd
[    2.436422] usb usb6: SerialNumber: xhci-hcd.5.auto
[    2.436530] hub 6-0:1.0: USB hub found
[    2.436539] hub 6-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    2.436625] usbcore: registered new interface driver cdc_acm
[    2.436629] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.436701] usbcore: registered new interface driver uas
[    2.436739] usbcore: registered new interface driver usb-storage
[    2.436765] usbcore: registered new interface driver usbserial_generic
[    2.436772] usbserial: USB Serial support registered for generic
[    2.436784] usbcore: registered new interface driver cp210x
[    2.436791] usbserial: USB Serial support registered for cp210x
[    2.436812] usbcore: registered new interface driver ftdi_sio
[    2.436819] usbserial: USB Serial support registered for FTDI USB Serial Device
[    2.436873] usbcore: registered new interface driver keyspan
[    2.436880] usbserial: USB Serial support registered for Keyspan - (without firmware)
[    2.436887] usbserial: USB Serial support registered for Keyspan 1 port adapter
[    2.436893] usbserial: USB Serial support registered for Keyspan 2 port adapter
[    2.436901] usbserial: USB Serial support registered for Keyspan 4 port adapter
[    2.436914] usbcore: registered new interface driver option
[    2.436921] usbserial: USB Serial support registered for GSM modem (1-port)
[    2.437002] usbcore: registered new interface driver oti6858
[    2.437010] usbserial: USB Serial support registered for oti6858
[    2.437021] usbcore: registered new interface driver pl2303
[    2.437027] usbserial: USB Serial support registered for pl2303
[    2.437043] usbcore: registered new interface driver qcserial
[    2.437050] usbserial: USB Serial support registered for Qualcomm USB modem
[    2.437069] usbcore: registered new interface driver sierra
[    2.437076] usbserial: USB Serial support registered for Sierra USB modem
[    2.437415] <<-GTP-INFO->> GTP driver installing...
[    2.437485] usbcore: registered new interface driver usbtouchscreen
[    2.437531] ata1: SATA link down (SStatus 0 SControl 300)
[    2.438313] input: rk805 pwrkey as /devices/platform/feb20000.spi/spi_master/spi2/spi2.0/rk805-pwrkey.3.auto/input/input0
[    2.438477] i2c /dev entries driver
[    2.441216] vdd_cpu_big0_s0: supplied by vcc5v0_sys
[    2.448967] vdd_cpu_big1_s0: supplied by vcc5v0_sys
[    2.457073] vdd_npu_s0: supplied by vcc5v0_sys
[    2.463368] i2c i2c-4: 1 i2c clients have been registered at 0x68
[    2.465094] rtc-hym8563 4-0051: rtc information is valid
[    2.470541] rtc-hym8563 4-0051: registered as rtc0
[    2.471607] rtc-hym8563 4-0051: setting system clock to 2021-01-01T12:08:39 UTC (1609502919)
[    2.473837] <<-GTP-INFO->> GTP Driver Version: V2.4<2014/11/28>
[    2.473844] <<-GTP-INFO->> GTP I2C Address: 0x5d
[    2.473882] <<-GTP-INFO->> Guitar reset
[    2.551256] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    2.579423] <<-GTP-INFO->> IC Version: 911_1060
[    2.603894] <<-GTP-INFO->> Sensor_ID: 2
[    2.603897] sensor_id = 2
[    2.603901] <<-GTP-INFO->> get goodix,cfg-group2
[    2.603906] <<-GTP-INFO->> Config group2 used,length: 186
[    2.604976] <<-GTP-INFO->> Driver send config.
[    2.627187] <<-GTP-INFO->> X_MAX: 1200, Y_MAX: 1920, TRIGGER: 0x01
[    2.641237] <<-GTP-INFO->> create proc entry gt9xx_config success
[    2.641289] input: goodix-ts as /devices/virtual/input/input1
[    2.641341] <<-GTP-INFO->> GTP works in interrupt mode.
[    2.641346] <<-GTP-INFO->> Applied memory size:2562.
[    2.641349] <<-GTP-INFO->> I2C function: without pre and end cmd!
[    2.641354] <<-GTP-INFO->> Create proc entry success!
[    2.641799] husb311 6-004e: fail to read Vendor id(-6)
[    2.641804] husb311 6-004e: check vid/pid fail(-6)
[    2.642596] ircut cam_ircut: driver version: 00.01.00
[    2.642655] ircut cam_ircut: failed get pulse-width,use dafult value 100
[    2.642667] ircut cam_ircut: Failed to get ircut-open-gpios
[    2.642675] ircut cam_ircut: Failed to get ircut-close-gpios
[    2.642687] ircut cam_ircut: probe successful!
[    2.643060] rkcifhw fdce0000.rkcif: Adding to iommu group 15
[    2.643844] rkcifhw fdce0000.rkcif: No reserved memory region assign to CIF
[    2.643903] rkcif rkcif-mipi-lvds2: Adding to iommu group 15
[    2.643914] rkcif rkcif-mipi-lvds2: rkcif driver version: v00.02.00
[    2.643955] rkcif rkcif-mipi-lvds2: attach to cif hw node
[    2.643959] rkcif rkcif-mipi-lvds2: rkcif wait line 0
[    2.643964] : terminal subdev does not exist
[    2.643967] : terminal subdev does not exist
[    2.643970] : terminal subdev does not exist
[    2.643973] : terminal subdev does not exist
[    2.643977] : get_remote_sensor: video pad[0] is null
[    2.643981] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[    2.643986] : rkcif_scale_set_fmt: req(80, 60) src out(0, 0)
[    2.643989] : get_remote_sensor: video pad[0] is null
[    2.643992] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[    2.643996] : rkcif_scale_set_fmt: req(80, 60) src out(0, 0)
[    2.643999] : get_remote_sensor: video pad[0] is null
[    2.644001] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[    2.644005] : rkcif_scale_set_fmt: req(80, 60) src out(0, 0)
[    2.644008] : get_remote_sensor: video pad[0] is null
[    2.644011] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[    2.644014] : rkcif_scale_set_fmt: req(80, 60) src out(0, 0)
[    2.644461] rkcif rkcif-mipi-lvds2: No memory-region-thunderboot specified
[    2.645083] rockchip-mipi-csi2-hw fdd10000.mipi0-csi2-hw: enter mipi csi2 hw probe!
[    2.645139] rockchip-mipi-csi2-hw fdd10000.mipi0-csi2-hw: probe success, v4l2_dev:mipi0-csi2-hw!
[    2.645164] rockchip-mipi-csi2-hw fdd20000.mipi1-csi2-hw: enter mipi csi2 hw probe!
[    2.645200] rockchip-mipi-csi2-hw fdd20000.mipi1-csi2-hw: probe success, v4l2_dev:mipi1-csi2-hw!
[    2.645221] rockchip-mipi-csi2-hw fdd30000.mipi2-csi2-hw: enter mipi csi2 hw probe!
[    2.645256] rockchip-mipi-csi2-hw fdd30000.mipi2-csi2-hw: probe success, v4l2_dev:mipi2-csi2-hw!
[    2.645275] rockchip-mipi-csi2-hw fdd40000.mipi3-csi2-hw: enter mipi csi2 hw probe!
[    2.645307] rockchip-mipi-csi2-hw fdd40000.mipi3-csi2-hw: probe success, v4l2_dev:mipi3-csi2-hw!
[    2.645327] rockchip-mipi-csi2-hw fdd50000.mipi4-csi2-hw: enter mipi csi2 hw probe!
[    2.645361] rockchip-mipi-csi2-hw fdd50000.mipi4-csi2-hw: probe success, v4l2_dev:mipi4-csi2-hw!
[    2.645381] rockchip-mipi-csi2-hw fdd60000.mipi5-csi2-hw: enter mipi csi2 hw probe!
[    2.645414] rockchip-mipi-csi2-hw fdd60000.mipi5-csi2-hw: probe success, v4l2_dev:mipi5-csi2-hw!
[    2.645737] rockchip-mipi-csi2 mipi2-csi2: attach to csi2 hw node
[    2.645754] rkcif rkcif-mipi-lvds2: Entity type for entity rockchip-mipi-csi2 was not initialized!
[    2.645759] rockchip-mipi-csi2: Async registered subdev
[    2.645763] rockchip-mipi-csi2: probe success, v4l2_dev:rkcif-mipi-lvds2!
[    2.646388] rkisp_hw fdcb0000.rkisp: Adding to iommu group 14
[    2.646507] rkisp_hw fdcb0000.rkisp: is_thunderboot: 0
[    2.646512] rkisp_hw fdcb0000.rkisp: Missing rockchip,grf property
[    2.646524] rkisp_hw fdcb0000.rkisp: max input:0x0@0fps
[    2.646575] rkisp_hw fdcb0000.rkisp: no find phandle sram
[    2.646762] rkisp rkisp0-vir0: rkisp driver version: v02.04.00
[    2.646816] rkisp rkisp0-vir0: No memory-region-thunderboot specified
[    2.646859] rkisp rkisp0-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
[    2.647881] rk_hdmirx fdee0000.hdmirx-controller: No reserved memory for HDMIRX, use default CMA
[    2.647912] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_probe: cpu_aff:0x500, Bound_cpu:5, wdt_cfg_bound_cpu:6, phy_cpuid:5
[    2.648392] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_audio_interrupts_setup: 0
[    2.648930] rk_hdmirx fdee0000.hdmirx-controller: rk_hdmirx_hdcp_register success
[    2.648948] rk_hdmirx fdee0000.hdmirx-controller: fdee0000.hdmirx-controller driver probe ok!
[    2.649026] usbcore: registered new interface driver uvcvideo
[    2.649029] USB Video Class driver (1.1.1)
[    2.649608] Bluetooth: HCI UART driver ver 2.3
[    2.649614] Bluetooth: HCI UART protocol H4 registered
[    2.649617] Bluetooth: HCI UART protocol ATH3K registered
[    2.649635] usbcore: registered new interface driver bfusb
[    2.649654] usbcore: registered new interface driver btusb
[    2.650354] cpu cpu0: bin=0
[    2.650562] cpu cpu0: leakage=10
[    2.651960] cpu cpu0: pvtm=1440
[    2.652074] cpu cpu0: pvtm-volt-sel=2
[    2.653933] cpu cpu4: bin=0
[    2.654137] cpu cpu4: leakage=9
[    2.660581] cpu cpu4: pvtm=1661
[    2.664486] cpu cpu4: pvtm-volt-sel=3
[    2.667103] cpu cpu6: bin=0
[    2.667307] cpu cpu6: leakage=9
[    2.673769] cpu cpu6: pvtm=1652
[    2.677690] cpu cpu6: pvtm-volt-sel=3
[    2.679408] cpu cpu0: avs=0
[    2.680386] cpu cpu4: avs=0
[    2.681206] cpu cpu6: avs=0
[    2.681394] cpu cpu0: EM: created perf domain
[    2.681422] cpu cpu0: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=1608000000 h_table=0
[    2.681908] cpu cpu4: EM: created perf domain
[    2.681931] cpu cpu4: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=2208000000 h_table=0
[    2.690214] cpu cpu6: EM: created perf domain
[    2.690723] cpu cpu6: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=2208000000 h_table=0
[    2.698569] usb 1-1: New USB device found, idVendor=1a40, idProduct=0201, bcdDevice= 1.00
[    2.698626] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.698642] usb 1-1: Product: USB 2.0 Hub [MTT]
[    2.699373] hub 1-1:1.0: USB hub found
[    2.699561] hub 1-1:1.0: 7 ports detected
[    2.706245] sdhci: Secure Digital Host Controller Interface driver
[    2.706278] sdhci: Copyright(c) Pierre Ossman
[    2.706285] Synopsys Designware Multimedia Card Interface Driver
[    2.707151] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.707631] dwmmc_rockchip fe2c0000.mmc: No normal pinctrl state
[    2.707643] dwmmc_rockchip fe2c0000.mmc: No idle pinctrl state
[    2.707853] dwmmc_rockchip fe2c0000.mmc: IDMAC supports 32-bit address mode.
[    2.707914] dwmmc_rockchip fe2c0000.mmc: Using internal DMA controller.
[    2.707927] dwmmc_rockchip fe2c0000.mmc: Version ID is 270a
[    2.707967] dwmmc_rockchip fe2c0000.mmc: DW MMC controller at irq 95,32 bit host data width,256 deep fifo
[    2.708352] dwmmc_rockchip fe2c0000.mmc: Failed getting OCR mask: -22
[    2.708556] dwmmc_rockchip fe2c0000.mmc: could not set regulator OCR (-22)
[    2.708565] dwmmc_rockchip fe2c0000.mmc: failed to enable vmmc regulator
[    2.709117] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[    2.709176] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[    2.710084] cryptodev: driver 1.12 loaded.
[    2.710104] hid: raw HID events driver (C) Jiri Kosina
[    2.710190] usbcore: registered new interface driver usbhid
[    2.710193] usbhid: USB HID core driver
[    2.719022] optee: probing for conduit method.
[    2.719047] optee: revision 3.13 (62aa10b7)
[    2.719372] optee: dynamic shared memory is enabled
[    2.719499] optee: initialized driver
[    2.720108] usbcore: registered new interface driver snd-usb-audio
[    2.721312] ES8323 7-0011: i2c recv Failed
[    2.723730] rockchip-i2s-tdm fddf0000.i2s: CLK-ALWAYS-ON: mclk: 12288000, bclk: 3072000, fsync: 48000
[    2.726033] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    2.726511] rockchip-i2s-tdm fddf4000.i2s: CLK-ALWAYS-ON: mclk: 12288000, bclk: 3072000, fsync: 48000
[    2.728633] debugfs: File 'Capture' in directory 'dapm' already present!
[    2.737201] mmc0: SDHCI controller on fe2e0000.mmc [fe2e0000.mmc] using ADMA
[    2.740951] input: rockchip,hdmiin rockchip,hdmiin as /devices/platform/hdmiin-sound/sound/card0/input2
[    2.742101] Initializing XFRM netlink socket
[    2.742351] NET: Registered protocol family 10
[    2.742753] Segment Routing with IPv6
[    2.742799] NET: Registered protocol family 17
[    2.742811] NET: Registered protocol family 15
[    2.742900] Bluetooth: RFCOMM socket layer initialized
[    2.742911] Bluetooth: RFCOMM ver 1.11
[    2.742918] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    2.742924] Bluetooth: HIDP socket layer initialized
[    2.742950] [BT_RFKILL]: Enter rfkill_rk_init
[    2.742955] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    2.743200] rockchip-pinctrl pinctrl: unable to find group for node wifi-poweren-gpio
[    2.743212] wlan-platdata: probe of wireless-wlan failed with error -22
[    2.743659] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 148.
[    2.743675] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 0.
[    2.743705] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 75.
[    2.743714] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 72.
[    2.743762] [BT_RFKILL]: Request irq for bt wakeup host
[    2.743808] [BT_RFKILL]: ** disable irq
[    2.743855] [BT_RFKILL]: bt_default device registered.
[    2.743905] Key type dns_resolver registered
[    2.744587] imx415 3-001a: driver version: 00.01.08
[    2.744596] imx415 3-001a:  Get hdr mode failed! no hdr default
[    2.744608] imx415 3-001a: detect imx415 lane 4
[    2.744629] imx415 3-001a: Failed to get reset-gpios
[    2.744640] imx415 3-001a: Failed to get power-gpios
[    2.744649] imx415 3-001a: could not get default pinstate
[    2.744653] imx415 3-001a: could not get sleep pinstate
[    2.744675] imx415 3-001a: supply dvdd not found, using dummy regulator
[    2.744736] imx415 3-001a: supply dovdd not found, using dummy regulator
[    2.777728] mmc0: Host Software Queue enabled
[    2.777751] mmc0: new HS400 Enhanced strobe MMC card at address 0001
[    2.778021] mmcblk0: mmc0:0001 SPeMMC 58.2 GiB 
[    2.778112] mmcblk0boot0: mmc0:0001 SPeMMC partition 1 4.00 MiB
[    2.778204] mmcblk0boot1: mmc0:0001 SPeMMC partition 2 4.00 MiB
[    2.778340] mmcblk0rpmb: mmc0:0001 SPeMMC partition 3 4.00 MiB, chardev (236:0)
[    2.780971]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
[    2.814832] imx415 3-001a: Unexpected sensor id(000000), ret(-5)
[    2.815520] Loading compiled-in X.509 certificates
[    2.816146] pstore: Using crash dump compression: deflate
[    2.816537] rga3_core0 fdb60000.rga: Adding to iommu group 2
[    2.816720] rga: rga3_core0, irq = 35, match scheduler
[    2.817236] rga: rga3_core0 hardware loaded successfully, hw_version:3.0.76831.
[    2.817277] rga: rga3_core0 probe successfully
[    2.817744] rga3_core1 fdb70000.rga: Adding to iommu group 3
[    2.817890] rga: rga3_core1, irq = 36, match scheduler
[    2.818222] rga: rga3_core1 hardware loaded successfully, hw_version:3.0.76831.
[    2.818285] rga: rga3_core1 probe successfully
[    2.818629] rga: rga2, irq = 37, match scheduler
[    2.818980] rga: rga2 hardware loaded successfully, hw_version:3.2.63318.
[    2.818994] rga: rga2 probe successfully
[    2.819184] rga_iommu: IOMMU binding successfully, default mapping core[0x1]
[    2.819421] rga: Module initialized. v1.3.1
[    2.840654] pcie20_avdd0v85: supplied by vdd_0v85_s0
[    2.840820] mali fb000000.gpu: Kernel DDK version g18p0-01eac0
[    2.845101] pcie20_avdd1v8: supplied by avcc_1v8_s0
[    2.845132] mali fb000000.gpu: bin=0
[    2.845349] mali fb000000.gpu: leakage=15
[    2.845392] debugfs: Directory 'fb000000.gpu-mali' with parent 'vdd_gpu_s0' already present!
[    2.845548] pcie30_avdd0v75: supplied by avdd_0v75_s0
[    2.845980] pcie30_avdd1v8: supplied by avcc_1v8_s0
[    2.846396] vcc3v3_lcd0_n: supplied by vcc_1v8_s0
[    2.846755] mali fb000000.gpu: pvtm=866
[    2.846911] mali fb000000.gpu: pvtm-volt-sel=3
[    2.847197] mpp_rkvenc2 fdbd0000.rkvenc-core: Adding to iommu group 10
[    2.847538] mpp_rkvenc2 fdbd0000.rkvenc-core: probing start
[    2.848268] mali fb000000.gpu: avs=0
[    2.848310] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 143; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[    2.848453] mpp_rkvenc2 fdbd0000.rkvenc-core: bin=0
[    2.848700] mpp_rkvenc2 fdbd0000.rkvenc-core: leakage=12
[    2.848713] mpp_rkvenc2 fdbd0000.rkvenc-core: leakage-volt-sel=0
[    2.849355] mpp_rkvenc2 fdbd0000.rkvenc-core: avs=0
[    2.849379] mpp_rkvenc2 fdbd0000.rkvenc-core: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[    2.850091] vendor storage:20190527 ret = 0
[    2.850604] mpp_rkvenc2 fdbd0000.rkvenc-core: attach ccu as core 0
[    2.850697] mali fb000000.gpu: r0p0 status 5 not found in HW issues table;
[    2.850709] mali fb000000.gpu: falling back to closest match: r0p0 status 0
[    2.850716] mali fb000000.gpu: Execution proceeding normally with fallback match
[    2.850724] mali fb000000.gpu: GPU identified as 0x7 arch 10.8.6 r0p0 status 0
[    2.850770] mali fb000000.gpu: No priority control manager is configured
[    2.850898] mali fb000000.gpu: No memory group manager is configured
[    2.850923] mali fb000000.gpu: Protected memory allocator not available
[    2.850980] mpp_rkvenc2 fdbd0000.rkvenc-core: probing finish
[    2.851202] mpp_rkvenc2 fdbe0000.rkvenc-core: Adding to iommu group 11
[    2.851588] mpp_rkvenc2 fdbe0000.rkvenc-core: probing start
[    2.851723] mali fb000000.gpu: Capping CSF_FIRMWARE_TIMEOUT to CSF_FIRMWARE_PING_TIMEOUT
[    2.852171] mali fb000000.gpu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0
[    2.852724] mpp_rkvenc2 fdbe0000.rkvenc-core: bin=0
[    2.852939] mpp_rkvenc2 fdbe0000.rkvenc-core: leakage=12
[    2.852950] mpp_rkvenc2 fdbe0000.rkvenc-core: leakage-volt-sel=0
[    2.853586] mpp_rkvenc2 fdbe0000.rkvenc-core: avs=0
[    2.853608] mpp_rkvenc2 fdbe0000.rkvenc-core: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[    2.853927] mpp_rkvenc2 fdbe0000.rkvenc-core: attach ccu as core 1
[    2.853976] mali fb000000.gpu: Probed as mali0
[    2.854213] mpp_rkvenc2 fdbe0000.rkvenc-core: probing finish
[    2.855951] rockchip-dmc dmc: bin=0
[    2.856130] rockchip-dmc dmc: leakage=35
[    2.856143] rockchip-dmc dmc: leakage-volt-sel=1
[    2.856156] rockchip-dmc dmc: soc version=0, speed=1
[    2.857041] rockchip-dmc dmc: avs=0
[    2.857055] rockchip-dmc dmc: current ATF version 0x100
[    2.857145] rockchip-dmc dmc: normal_rate = 1560000000
[    2.857153] rockchip-dmc dmc: reboot_rate = 2112000000
[    2.857161] rockchip-dmc dmc: suspend_rate = 528000000
[    2.857168] rockchip-dmc dmc: video_4k_rate = 1560000000
[    2.857175] rockchip-dmc dmc: video_4k_10b_rate = 1560000000
[    2.857182] rockchip-dmc dmc: video_svep_rate = 1560000000
[    2.857189] rockchip-dmc dmc: boost_rate = 2112000000
[    2.857196] rockchip-dmc dmc: fixed_rate(isp|cif0|cif1|dualview) = 2112000000
[    2.857203] rockchip-dmc dmc: performance_rate = 2112000000
[    2.857211] rockchip-dmc dmc: hdmirx_rate = 2112000000
[    2.857217] rockchip-dmc dmc: deep_suspend_rate = 2112000000
[    2.857227] rockchip-dmc dmc: failed to get vop bandwidth to dmc rate
[    2.857233] rockchip-dmc dmc: failed to get vop pn to msch rl
[    2.857368] rockchip-dmc dmc: l=10000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    2.858936] rockchip-dmc dmc: could not find power_model node
[    2.878149] rockchip-csi2-dphy csi2-dphy0: csi2 dphy0 probe successfully!
[    2.884035] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2
[    2.884073] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3
[    2.884086] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8
[    2.884099] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9
[    2.884527] [drm] failed to init overlay plane Cluster0-win1
[    2.884597] [drm] failed to init overlay plane Cluster1-win1
[    2.884648] [drm] failed to init overlay plane Cluster2-win1
[    2.884700] [drm] failed to init overlay plane Cluster3-win1
[    2.908292] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffffffc00935e230)
[    2.909701] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[    2.910886] dw-hdmi-qp-hdcp dw-hdmi-qp-hdcp.9.auto: dw_hdcp_qp_hdcp_probe success
[    2.910984] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffffffc00936cdc0)
[    2.912555] dwhdmi-rockchip fdea0000.hdmi: registered ddc I2C bus driver
[    2.913659] dw-hdmi-qp-hdcp dw-hdmi-qp-hdcp.12.auto: dw_hdcp_qp_hdcp_probe success
[    2.913739] rockchip-drm display-subsystem: bound fdea0000.hdmi (ops 0xffffffc00936cdc0)
[    2.913772] dw-mipi-dsi2 fde20000.dsi: [drm:dw_mipi_dsi2_bind] *ERROR* Failed to find panel or bridge: -517
[    2.921043] input: adc-keys as /devices/platform/adc-keys/input/input3
[    2.926943] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2
[    2.926967] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3
[    2.926975] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8
[    2.926985] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9
[    2.927263] [drm] failed to init overlay plane Cluster0-win1
[    2.927296] [drm] failed to init overlay plane Cluster1-win1
[    2.927328] [drm] failed to init overlay plane Cluster2-win1
[    2.927367] [drm] failed to init overlay plane Cluster3-win1
[    2.944508] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffffffc00935e230)
[    2.946809] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[    2.949067] dw-hdmi-qp-hdcp dw-hdmi-qp-hdcp.9.auto: dw_hdcp_qp_hdcp_probe success
[    2.949204] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffffffc00936cdc0)
[    2.950676] dwhdmi-rockchip fdea0000.hdmi: registered ddc I2C bus driver
[    2.952511] dw-hdmi-qp-hdcp dw-hdmi-qp-hdcp.12.auto: dw_hdcp_qp_hdcp_probe success
[    2.952617] rockchip-drm display-subsystem: bound fdea0000.hdmi (ops 0xffffffc00936cdc0)
[    2.952721] rockchip-drm display-subsystem: bound fde20000.dsi (ops 0xffffffc00936f5d8)
[    2.952830] rockchip-drm display-subsystem: bound fde50000.dp (ops 0xffffffc00936f968)
[    2.952919] rockchip-drm display-subsystem: bound fde60000.dp (ops 0xffffffc00936f968)
[    2.966051] rockchip-drm display-subsystem: route-hdmi0: failed to get logo,offset
[    2.966075] rockchip-drm display-subsystem: route-hdmi1: failed to get logo,offset
[    2.978285] rockchip-drm display-subsystem: [drm] fb0: rockchipdrmfb frame buffer device
[    2.979323] [drm] Initialized rockchip 3.0.0 20140818 for display-subsystem on minor 0
[    2.982019] input: rockchip-hdmi0 rockchip-hdmi0 as /devices/platform/hdmi0-sound/sound/card1/input4
[    2.984851] input: rockchip-hdmi1 rockchip-hdmi1 as /devices/platform/hdmi1-sound/sound/card2/input5
[    2.990091] rkcif rkcif-mipi-lvds2: clear unready subdev num: 1
[    2.990852] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[    2.990895] rkcif-mipi-lvds2: Async subdev notifier completed
[    2.990920] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[    2.990930] rkcif-mipi-lvds2: There is not terminal subdev, not synchronized with ISP
[    2.991061] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[    2.991076] rkcif-mipi-lvds2: There is not terminal subdev, not synchronized with ISP
[    2.993130] RKNPU fdab0000.npu: Adding to iommu group 0
[    2.993389] RKNPU fdab0000.npu: RKNPU: rknpu iommu is enabled, using iommu mode
[    2.994987] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdab0000-0xfdabffff]
[    2.995034] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdac0000-0xfdacffff]
[    2.995058] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdad0000-0xfdadffff]
[    2.995747] [drm] Initialized rknpu 0.9.3 20231121 for fdab0000.npu on minor 1
[    2.999961] RKNPU fdab0000.npu: RKNPU: bin=0
[    3.000237] RKNPU fdab0000.npu: leakage=8
[    3.000299] debugfs: Directory 'fdab0000.npu-rknpu' with parent 'vdd_npu_s0' already present!
[    3.007947] RKNPU fdab0000.npu: pvtm=869
[    3.012795] RKNPU fdab0000.npu: pvtm-volt-sel=3
[    3.014197] RKNPU fdab0000.npu: avs=0
[    3.014416] RKNPU fdab0000.npu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0
[    3.035071] RKNPU fdab0000.npu: failed to find power_model node
[    3.035101] RKNPU fdab0000.npu: RKNPU: failed to initialize power model
[    3.035109] RKNPU fdab0000.npu: RKNPU: failed to get dynamic-coefficient
[    3.041011] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    3.043435] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    3.043712] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    3.043723] cfg80211: failed to load regulatory.db
[    3.045181] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[    3.045901] rockchip-suspend not set sleep-mode-config for mem-lite
[    3.045909] rockchip-suspend not set wakeup-config for mem-lite
[    3.045918] rockchip-suspend not set sleep-mode-config for mem-ultra
[    3.045925] rockchip-suspend not set wakeup-config for mem-ultra
[    3.047280] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 406; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '10:10:23', on 'Nov 27 2025'.
[    3.047643] Mali: 
[    3.047647] Mali device driver loaded
[    3.047668] rkisp rkisp0-vir0: clear unready subdev num: 1
[    3.047890] rkisp0-vir0: Async subdev notifier completed
[    3.047916] ALSA device list:
[    3.047924]   #0: rockchip,hdmiin
[    3.047931]   #1: rockchip-hdmi0
[    3.047938]   #2: rockchip-hdmi1
[    3.052587] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)
[    3.052643] VFS: Mounted root (ext4 filesystem) on device 179:6.
[    3.053148] devtmpfs: mounted
[    3.059611] Freeing unused kernel memory: 6720K
[    3.085058] Run /sbin/init as init process
[    3.133884] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
[    3.256824] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null)
[    3.260112] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: (null)
Start mounting all internal partitions in /etc/fstab
Log saved to /var/log/mount-all.log
Note: Will skip fsck, remove /.skip_fsck to enable
[2]: Handling /dev/mmcblk0p8 /userdata ext4 defaults 2
[0]: Handling /dev/mmcblk0p6 / ext4 rw,noauto 1
[1]: Handling /dev/mmcblk0p7 /oem ext4 defaults 2
[2]: Resizing /dev/mmcblk0p8(ext4)
[1]: Resizing /dev/mmcblk0p7(ext4)
[0]: Resizing /dev/mmcblk0p6(ext4)
resize2fs 1.46.5 (30-Dec-2021)
resize2fs 1.46.5 (30-Dec-2021)
resize2fs 1.46.5 (30-Dec-2021)
[    3.376966] EXT4-fs (mmcblk0p7): resizing filesystem from 17056 to 131072 blocks
[    3.377486] EXT4-fs (mmcblk0p8): resizing filesystem from 4376 to 46014432 blocks
[    3.377507] EXT4-fs (mmcblk0p6): resizing filesystem from 209664 to 3670016 blocks
[    3.570681] EXT4-fs (mmcblk0p6): resized filesystem to 3670016
Filesystem at /dev/mmcblk0p6 is mounted on /; on-line resizing required
old_desc_blocks = 1, new_desc_blocks = 1
The filesystem on /dev/mmcblk0p6 is now 3670016 (4k) blocks long.

[    3.614040] EXT4-fs (mmcblk0p7): resized filesystem to 131072
Filesystem at /dev/mmcblk0p7 is mounted on /oem; on-line resizing required
old_desc_blocks = 1, new_desc_blocks = 1
The filesystem on /dev/mmcblk0p7 is now 131072 (1k) blocks long.

[    3.998355] EXT4-fs (mmcblk0p8): resizing filesystem from 4587521 to 46014432 blocks
[    3.998410] EXT4-fs (mmcblk0p8): Converting file system to meta_bg
[    3.998470] EXT4-fs (mmcblk0p8): resizing filesystem from 4587521 to 46014432 blocks
[    4.695842] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_cancel_cpu_limit_freq freq qos nod add
[    7.244453] EXT4-fs (mmcblk0p8): resized filesystem to 46014432
Filesystem at /dev/mmcblk0p8 is mounted on /userdata; on-line resizing required
old_desc_blocks = 1, new_desc_blocks = 352
The filesystem on /dev/mmcblk0p8 is now 46014432 (1k) blocks long.

Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
Populating /dev using udev: [    7.434553] udevd[427]: starting version 3.2.10
[    7.463774] udevd[433]: starting eudev-3.2.10
[    7.567090] r8168 0004:41:00.0 enP4p65s0: renamed from eth1
[    7.568665] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[    7.568686] stream_cif_mipi_id1: update sensor info failed -19
[    7.568845] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[    7.568858] rkcif_tools_id2: update sensor info failed -19
[    7.569672] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[    7.569684] rkcif_scale_ch0: update sensor info failed -19
[    7.569750] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[    7.569756] rkcif_tools_id1: update sensor info failed -19
[    7.569805] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[    7.569814] stream_cif_mipi_id0: update sensor info failed -19
[    7.569841] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed!
[    7.569850] rkcif_scale_ch3: update sensor info failed -19
[    7.570202] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[    7.570212] stream_cif_mipi_id2: update sensor info failed -19
[    7.570601] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[    7.570608] rkcif_scale_ch2: update sensor info failed -19
[    7.572616] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[    7.572652] rkcif_tools_id0: update sensor info failed -19
[    7.573666] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[    7.573696] rkcif_scale_ch1: update sensor info failed -19
[    7.574899] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed!
[    7.574923] stream_cif_mipi_id3: update sensor info failed -19
done
Starting irqbalance: OK
Saving random seed: OK
Starting system message bus: done
Starting bluetoothd: OK
Starting network: ln: failed to create symbolic link '': No such file or directory
OK
Starting dhcpcd...
dhcpcd-9.4.1 starting
DHCPCD_ARGS: interface not found
dhcpcd exited
Starting ntpd: OK
starting weston... done.
Starting dropbear sshd: OK
Starting pulseaudio: OK
Starting dnsmasq: OK
Starting input-event-daemon: done
W: [pulseaudio] main.c: This program is not intended to be run as root (unless --system is specified).
W: [pulseaudio] main.c: Compiled with DEPRECATED libsamplerate support!
root@rk3588-buildroot:/# Handling start for Wi-Fi/BT chip: Broadcom    AP6275P    pci    14e4:449d    bcmdhd_pcie.ko
Starting Wifi/BT...
Installing WiFi/BT module: bcmdhd_pcie.ko
Date: 2021-01-01 UTC
[12:08:45.237] weston 13.0.0
               https://wayland.freedesktop.org
               Bug reports to: https://gitlab.freedesktop.org/wayland/weston/issues/
               Build: 13.0.0
[12:08:45.240] Command line: /usr/bin/weston
[12:08:45.240] OS: Linux, 5.10.198, #2 SMP Thu Nov 27 13:44:36 CST 2025, aarch64
[12:08:45.240] Flight recorder: enabled
[12:08:45.240] warning: XDG_RUNTIME_DIR "/var/run" is not configured
correctly.  Unix access mode must be 0700 (current mode is 0755),
and must be owned by the user UID 0 (current owner is UID 0).
Refer to your distribution on how to get it, or
http://www.freedesktop.org/wiki/Specifications/basedir-spec
on how to implement it.
[    8.222009] bcmdhd_pcie: loading out-of-tree module taints kernel.
[    8.222082] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_audio_startup: device is no connected or audio is off
/etc/xdg/weston/weston.ini.d/02-desktop.ini: "shell/locking" from "false" to "true"
[    8.222091] hdmi-audio-codec hdmi-audio-codec.6.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[12:08:45.251] Using config file '/etc/xdg/weston/weston.ini'
[12:08:45.251] Output repaint window is -1 ms maximum.
[12:08:45.252] Loading module '/usr/lib/libweston-13/drm-backend.so'
[    8.226813] [dhd] _dhd_module_init: in Dongle Host Driver, version 101.10.591.46.22 (20231003-3)(a5ec15e)
[    8.226813] /home/jinhualong/new_disk_4t/wyb/RD-RK3588/repo_RK3588_Buildroot20240508/external/rkwifibt/drivers/bcmdhd compiled on Nov 27 2025 at 16:40:45
[12:08:45.256] initializing drm backend
[    8.226813] 
[12:08:45.256] Entering mirror mode.
[    8.226826] [dhd] STATIC-MSG) dhd_static_buf_init : 101.10.361.31 (wlan=r892223-20230427-1)
[12:08:45.256] Trying direct launcher...
[    8.226891] [dhd] STATIC-MSG) dhd_init_wlan_mem : prealloc ok for index 0: 2369536(2314K)
[12:08:45.258] using /dev/dri/card0
[    8.226895] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
[12:08:45.258] DRM: does not support atomic modesetting
[    8.226898] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: rfkill-wlan driver has not Successful initialized
[12:08:45.258] DRM: does not support GBM modifiers
[    8.226900] dhd_wlan_init_gpio: unknown oob irqflags !
[12:08:45.258] DRM: does not support async page flipping
[    8.226902] [dhd] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=-1, oob_irq_flags=0x0
[12:08:45.258] DRM: supports picture aspect ratio
[    8.226905] [dhd] dhd_wlan_init_gpio: WL_REG_ON=-1
[12:08:45.261] Loading module '/usr/lib/libweston-13/gl-renderer.so'
[    8.226907] [dhd] dhd_wifi_platform_load: Enter
arm_release_ver: g13p0-01eac0, rk_so_ver: 10
[    8.226915] [dhd] wifi_platform_bus_enumerate device present 1
[    8.226917] [dhd] ======== Card detection to detect PCIE card! ========
[    8.226992] [dhd] dhdpcie_pci_probe : no mutex held
[    8.226994] [dhd] dhdpcie_pci_probe : set mutex lock
[    8.226997] [dhd] PCI_PROBE:  bus 0x21, slot 0x0,vendor 0x14E4, device 0x449D(good PCI location)
[    8.227000] [dhd] dhdpcie_init: found adapter info 'DHD generic adapter'
[    8.227002] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 3, size 139264
[    8.227011] [dhd] succeed to alloc static buf
[    8.227013] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 4, size 0
[    8.227016] [dhd] dhdpcie_init: Host OOB irq is not defined
[    8.227058] pcieh 0002:21:00.0: enabling device (0000 -> 0002)
[    8.227388] [dhd] Disable CTO
[    8.228119] [dhd] DHD: dongle ram size is set to 1310720(orig 1310720) at 0x170000
[    8.228126] [dhd] dhdpcie_bar1_window_switch_enab: bar1_switch_enab=0 ramstart=0x170000 ramend=0x2affff bar1_size=0x0
[    8.228142] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 7, size 43776
[    8.228152] [dhd] dhd_conf_set_chiprev : devid=0x449d, chip=0xaae8, chiprev=2, svid=0x14e4, ssid=0xaae8
[    8.228277] [dhd] dhd_check_htput_chip: htput_support:1
[    8.228285] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 0, size 5152
[    8.233599] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_audio_startup: device is no connected or audio is off
[    8.233630] hdmi-audio-codec hdmi-audio-codec.6.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[    8.238293] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 5, size 65536
E: [pulseaudio] module-alsa-card.c: Failed to find a working profile.
[    8.238553] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 19, size 65688
E: [pulseaudio] module.c: Failed to load module "module-alsa-card" (argument: "device_id="0" name="platform-hdmiin-sound" card_name="alsa_card.platform-hdmiin-sound" namereg_fail=false tsched=no fixed_latency_range=no ignore_dB=no deferred_volume=yes use_ucm=yes avoid_resampling=no card_properties="module-udev-detect.discovered=1""): initialization failed.
[    8.238662] [dhd] dhd_attach(): thread:dhd_watchdog_thread:3e5 started
[    8.238668] [dhd] dhd_deferred_work_init: work queue initialized
[    8.238672] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 3
[    8.238674] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=40, TCPDATA_INFO_MAXNUM=40
[    8.238681] [dhd] dhd_cpumasks_init CPU masks primary(big)=0xf0 secondary(little)=0xe
[    8.238703] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[    8.238850] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[    8.238877] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[    8.238903] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[    8.238921] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[    8.238933] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[    8.238952] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[12:08:45.289] EGL version: 1.4 Valhall-"g13p0-01eac0"
[    8.239022] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[12:08:45.289] EGL vendor: ARM
[    8.239061] [dhd] dhdpcie_bus_attach: making DHD_BUS_DOWN
[12:08:45.289] EGL client APIs: OpenGL_ES
[    8.239067] [dhd] dhdpcie_init: rc_dev from dev->bus->self (1d87:3588) is 00000000f8c4ea03
[12:08:45.289] EGL features:
[    8.239265] [dhd] dhdpcie_init: rc_ep_aspm_cap: 1 rc_ep_l1ss_cap: 1
               EGL Wayland extension: yes
[    8.239273] [dhd] dhdpcie_request_irq: INTx enabled, irq=147
               context priority: yes
[    8.239292] [dhd] dhdpcie_bar1_window_switch_enab: bar1_switch_enab=0 ramstart=0x170000 ramend=0x2affff bar1_size=0x400000
               buffer age: no
[    8.239298] [dhd] dhd_bus_download_firmware: firmware path=/vendor/etc/firmware/fw_bcmdhd.bin, nvram path=/vendor/etc/firmware/nvram.txt
               partial update: yes
[    8.239307] [dhd] dhd_conf_set_path_params : Final fw_path=/vendor/etc/firmware/fw_bcm43752a2_pcie_ag.bin
               swap buffers with damage: no
[    8.239309] [dhd] dhd_conf_set_path_params : Final nv_path=/vendor/etc/firmware/nvram_ap6275p.txt
               configless context: yes
[    8.239312] [dhd] dhd_conf_set_path_params : Final clm_path=/vendor/etc/firmware/clm_bcm43752a2_pcie_ag.blob
               surfaceless context: yes
[    8.239314] [dhd] dhd_conf_set_path_params : Final conf_path=/vendor/etc/firmware/config.txt
               dmabuf support: modifiers
[    8.240987] [dhd] dhd_os_open_image1: /vendor/etc/firmware/config.txt (240 bytes) open success
W: [pulseaudio] authkey.c: Failed to open cookie file '/userdata/.pulse/.config/pulse/cookie': No such file or directory
[    8.241080] mali fb000000.gpu: Loading Mali firmware 0x1010000
W: [pulseaudio] authkey.c: Failed to load authentication key '/userdata/.pulse/.config/pulse/cookie': No such file or directory
[    8.241188] [dhd] dhd_conf_read_pm_params : PM = 0
W: [pulseaudio] authkey.c: Failed to open cookie file '/userdata/.pulse/.pulse-cookie': No such file or directory
[    8.241193] [dhd] dhd_conf_read_pm_params : pm_in_suspend = 2
W: [pulseaudio] authkey.c: Failed to load authentication key '/userdata/.pulse/.pulse-cookie': No such file or directory
[    8.241197] [dhd] dhd_conf_read_others : keep_alive_period = 120000
E: [pulseaudio] module-rescue-streams.c: module-rescue-stream is obsolete and should no longer be loaded. Please remove it from your configuration.
[    8.241200] [dhd] dhd_conf_read_others : garp = 1
E: [pulseaudio] module-console-kit.c: GetSessionsForUnixUser() call failed: org.freedesktop.DBus.Error.ServiceUnknown: The name org.freedesktop.ConsoleKit was not provided by any .service files
[    8.241203] [dhd] dhd_conf_read_pm_params : suspend_bcn_li_dtim = 10
E: [pulseaudio] module.c: Failed to load module "module-console-kit" (argument: ""): initialization failed.
[    8.241208] [dhd] dhd_conf_read_others : wl_preinit = pm2_sleep_ret=20
W: [pulseaudio] server-lookup.c: Unable to contact D-Bus: org.freedesktop.DBus.Error.NotSupported: Using X11 for dbus-daemon autolaunch was disabled at compile time, set your DBUS_SESSION_BUS_ADDRESS instead
[    8.241213] [dhd] dhd_conf_read_pkt_filter : pkt_filter_del id = 100 102 103 104 105 107 
W: [pulseaudio] main.c: Unable to contact D-Bus: org.freedesktop.DBus.Error.NotSupported: Using X11 for dbus-daemon autolaunch was disabled at compile time, set your DBUS_SESSION_BUS_ADDRESS instead
[    8.241222] [dhd] dhd_conf_read_pkt_filter : pkt_filter_add[0][] = 142 0 0 77 0xffffffffffffffffffffffffffffff 0x2F6465766963652F77616B6575702F
[12:08:45.310] GL version: OpenGL ES 3.2 v1.g13p0-01eac0.11addb9882ee8209dc0912af75110af7
[    8.241239] [dhd] d2h_intr_method -> PCIE_INTX(0); d2h_intr_control -> D2H_INTMASK(0)
[12:08:45.310] GLSL version: OpenGL ES GLSL ES 3.20
[    8.241436] [dhd] dhdpcie_download_code_file: dhd_tcm_test_enable 0, dhd_tcm_test_status 0
[12:08:45.310] GL vendor: ARM
[    8.241440] [dhd] dhdpcie_download_code_file: download firmware /vendor/etc/firmware/fw_bcm43752a2_pcie_ag.bin
[12:08:45.310] GL renderer: Mali-G610
[    8.241463] [dhd] dhd_os_open_image1: /vendor/etc/firmware/fw_bcm43752a2_pcie_ag.bin (936074 bytes) open success
[    8.241768] [dhd] dhd_os_open_image1: /vendor/etc/firmware/fw_bcm43752a2_pcie_ag.bin (936074 bytes) open success
[    8.241773] [dhd] dhdpcie_download_code_file Using SINGLE image (size 936074)
[    8.242842] mali fb000000.gpu: Mali firmware git_sha: ee476db42870778306fa8d559a605a73f13e455c 
[    8.245355] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_audio_startup: device is no connected or audio is off
[    8.245367] hdmi-audio-codec hdmi-audio-codec.6.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[    8.246137] file system registered
[    8.280940] read descriptors
[    8.280972] read strings
[    8.312421] [dhd] dhd_os_open_image1: /vendor/etc/firmware/nvram_ap6275p.txt (7458 bytes) open success
[    8.312711] [dhd] dhdpcie_download_nvram: dhd_get_download_buffer len 7458
[    8.312718] [dhd] # AP6275P_NVRAM_V1.2_20210918A
[    8.312746] [dhd] dhdpcie_download_nvram: process_nvram_vars len 6036
[    8.315933] dwc3 fc000000.usb: device reset
[    8.325836] android_work: sent uevent USB_STATE=CONNECTED
[    8.327155] [dhd] dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded.
[    8.327161] [dhd] dhdpcie_bus_write_vars: New varsize is 6040, length token(nvram_csm)=0xfa1905e6
[    8.327495] [dhd] Download and compare of TLV 0xfeedc0de succeeded (size 128, addr 2ae7dc).
[    8.327572] [dhd] dhdpcie_bus_download_state: Took ARM out of Reset
[    8.327593] [dhd] dhd_bus_aer_config: Configure AER registers for EP
[    8.327616] [dhd] dhd_bus_aer_config: Configure AER registers for RC
[    8.412769] android_work: sent uevent USB_STATE=CONFIGURED
[12:08:45.446] GL ES 3.2 - renderer features:
               read-back format: ARGB8888
               glReadPixels supports y-flip: no
               wl_shm 10 bpc formats: yes
               wl_shm 16 bpc formats: no
[    8.419354] [dhd] dhdpcie_readshared: addr=0x20a584 nvram_csm=0xfa1905e6
               wl_shm half-float formats: yes
[    8.419366] [dhd] ### Total time ARM OOR to Readshared pass took 91821 usec ###
               internal R and RG formats: yes
[    8.419370] [dhd] dhdpcie_readshared: PCIe shared addr (0x0020a584) read took 90000 usec before dongle is ready
               OES_EGL_image_external: yes
[    8.419635] [dhd] FW supports DAR ? N
               wl_shm sub-image to texture: yes
[    8.419687] [dhd] H2D DMA WR INDX : array size 172 = 4 * 43
[12:08:45.446] Using GL renderer
[    8.419693] [dhd] D2H DMA RD INDX : array size 16 = 4 * 4
[    8.419699] [dhd] D2H DMA WR INDX : array size 16 = 4 * 4
[    8.419706] [dhd] H2D DMA RD INDX : array size 172 = 4 * 43
[    8.419711] [dhd] dhdpcie_readshared: max H2D queues 40
[    8.419714] [dhd] FW supports debug buf dest ? N 
[    8.419718] [dhd] FW supports MD ring ? N
[    8.419859] [dhd] dhd_bus_init: Enabling bus->intr_enabled
[    8.419879] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 9, size 32896
[    8.419890] [dhd] dhd_prot_init:4138: h2d_max_txpost = 512
[    8.419893] [dhd] dhd_prot_init:4144: h2d_htput_max_txpost = 2048
[    8.419901] [dhd] dhd_prot_init: max_rxbufpost:511 rx_buf_burst:64 rx_bufpost_threshold:64
[    8.419905] [dhd] ENABLING DW:0
[    8.419908] [dhd] IDMA inited
[    8.419912] [dhd] IFRM not enabled in FW !!
[    8.419915] [dhd] DAR not enabled in FW !!
[    8.419918] [dhd] Enable hostcap: EXTD TXS in txcpl
[    8.419981] [dhd] dhd_prot_d2h_sync_init(): D2H sync mechanism is NONE 
[12:08:45.459] event3  - adc-keys: is tagged by udev as: Keyboard
[    8.419996] [dhd] dhd_bus_hostready : Read PCICMD Reg: 0x00100006
[12:08:45.459] event3  - adc-keys: device is a keyboard
[    8.420014] [dhd] dhd_bus_hostready: Ring Hostready:1
[12:08:45.460] event0  - rk805 pwrkey: is tagged by udev as: Keyboard
[    8.420018] [dhd] Attach flowrings pool for 40 rings
[12:08:45.460] event0  - rk805 pwrkey: device is a keyboard
[    8.420044] [dhd] iDMA enabled PCIEControl = 00000001
[12:08:45.460] event4  - rockchip-hdmi0 rockchip-hdmi0: is tagged by udev as: Switch
[    8.421606] [dhd] trying to send create d2h info ring: id 46
[12:08:45.460] event4  - not using input device '/dev/input/event4'
[    8.421622] [dhd] dhd_send_d2h_ringcreate ringid: 3 idx: 46 max_h2d: 43
[12:08:45.461] event5  - rockchip-hdmi1 rockchip-hdmi1: is tagged by udev as: Switch
[    8.421743] [dhd] trying to send create h2d info ring id 45
[12:08:45.461] event5  - not using input device '/dev/input/event5'
[    8.422118] [dhd] dhd_prot_process_d2h_ring_create_complete ring create Response status = 0 ring 3, id 0xfffc
[12:08:45.462] event2  - rockchip,hdmiin rockchip,hdmiin: is tagged by udev as: Switch
[    8.422131] [dhd] info buffer post after ring create
[12:08:45.462] event2  - not using input device '/dev/input/event2'
[    8.424001] [dhd] wlc_ver_major 12, wlc_ver_minor 1
[12:08:45.463] event1  - goodix-ts: is tagged by udev as: Keyboard Touchscreen
[    8.424535] [dhd] dhd_sync_with_dongle: GET_REVINFO device 0x449d, vendor 0x14e4, chipnum 0xaae8
[12:08:45.463] event1  - goodix-ts: device is a keyboard
[    8.426181] [dhd] dhd_sync_with_dongle: RxBuf Post : 2048
[12:08:45.463] event1  - goodix-ts: device is a touch device
[    8.426191] [dhd] dhd_sync_with_dongle: RxBuf Post Alloc : 2048
[    8.430218] [dhd] dhd_preinit_ioctls: preinit_status IOVAR not supported, use legacy preinit
[    8.430232] [dhd] dhd_tcpack_suppress_set 378: already set to 3
[    8.432124] [dhd] dhd_legacy_preinit_ioctls: hostwake_oob enabled
[    8.433413] [dhd] dhd_legacy_preinit_ioctls: use firmware generated mac_address c0:f5:35:4f:8d:5e
[    8.433474] [dhd] dhd_os_open_image1: /vendor/etc/firmware/clm_bcm43752a2_pcie_ag.blob (30993 bytes) open success
[    8.436325] [dhd] dhd_check_current_clm_data: ----- This FW is not included CLM data -----
[12:08:45.497] libinput: configuring device "adc-keys".
[12:08:45.497] libinput: configuring device "rk805 pwrkey".
[12:08:45.497] Touchscreen - goodix-ts - /sys/devices/virtual/input/input1/event1
[12:08:45.497] libinput: configuring device "goodix-ts".
[12:08:45.497] input device event1 has no enabled output associated (none named), skipping calibration for now.
[12:08:45.497] Registered plugin API 'weston_drm_output_api_v1' of size 40
[12:08:45.497] Color manager: no-op
[12:08:45.497] Compositor capabilities:
               arbitrary surface rotation: yes
               screen capture uses y-flip: yes
               cursor planes: yes
               arbitrary resolutions: no
               view mask clipping: yes
               explicit sync: yes
               color operations: yes
               presentation clock: CLOCK_MONOTONIC, id 1
               presentation clock resolution: 0.000000001 s
[12:08:45.498] Loading module '/usr/lib/weston/desktop-shell.so'
[12:08:45.500] DRM: head 'HDMI-A-1' found, connector 208 is disconnected.
[12:08:45.500] DRM: head 'HDMI-A-2' found, connector 224 is disconnected.
[12:08:45.500] DRM: head 'DSI-1' found, connector 238 is connected, EDID make 'unknown', model 'unknown', serial ''
[    8.478357] [dhd] dhd_apply_default_clm: CLM download succeeded 
               Supported EOTF modes: SDR
[12:08:45.500] DRM: head 'DP-1' found, connector 240 is disconnected.
[12:08:45.500] DRM: head 'DP-2' found, connector 248 is disconnected.
[12:08:45.500] launching '/usr/libexec/weston-keyboard'
[    8.480929] [dhd] dhd_check_current_clm_data: ----- This FW is included CLM data -----
[12:08:45.501] launching '/usr/libexec/weston-desktop-shell'
[12:08:45.502] DSI-1 using at least 2 buffers
[12:08:45.502] Output 'DSI-1' attempts EOTF mode: SDR
[12:08:45.502] Output 'DSI-1' using color profile: stock sRGB color profile
[12:08:45.503] Chosen EGL config details: id:   9 rgba: 8 8 8 0 buf: 24 dep:  0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[12:08:45.503] Output DSI-1 (crtc 137) video modes:
               1200x1920@55.8, preferred, current, 148.0 MHz
[12:08:45.503] associating input device event3 with output DSI-1 (none by udev)
[12:08:45.503] associating input device event0 with output DSI-1 (none by udev)
[12:08:45.503] associating input device event1 with output DSI-1 (none by udev)
[12:08:45.503] Output 'DSI-1' enabled with head(s) DSI-1
[    8.488521] [dhd] Firmware up: op_mode=0x0005, MAC=c0:f5:35:4f:8d:5e
[    8.517629] [dhd] dhd_legacy_preinit_ioctls: event_log_max_sets: 26 ret: 0
[    8.533414] [dhd] arp_enable:1 arp_ol:0
[    8.533461] [dhd] dhd_conf_add_pkt_filter : 142 0 0 77 0xffffffffffffffffffffffffffffff 0x2F6465766963652F77616B6575702F
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
[    8.556393] [dhd]   Driver: 101.10.591.46.22 (20231003-3)
[    8.556393] [dhd]   Firmware: wl0: Jul 12 2022 18:54:54 version 18.35.387.23.146 (g412cc5ec) FWID 01-93c53be6
[    8.556393] [dhd]   CLM: 9.9.12_SS (2021-10-12 17:03:28) 
[    8.638901] [dhd] dhd_ecounter_autoconfig Ecounter autoconfig in FW not supported
[    8.644766] [dhd] dhd_legacy_preinit_ioctls: d3_hostwake_delay IOVAR not present, proceed
[    8.677379] [dhd] dhd_update_interface_flow_info: ifindex:0 previous role:0 new role:0
[    8.677430] [dhd] dhd_rx_frame: net device is NOT registered. drop event packet
[    8.680314] [dhd] dhd_conf_set_country : set country CN, revision 0
[    8.685707] [dhd] dhd_conf_set_country : Country code: CN (CN/0)
[    8.710132] [dhd] Dongle Host Driver, version 101.10.591.46.22 (20231003-3)(a5ec15e)
[    8.710132] /home/jinhualong/new_disk_4t/wyb/RD-RK3588/repo_RK3588_Buildroot20240508/external/rkwifibt/drivers/bcmdhd compiled on Nov 27 2025 at 16:40:45
[    8.710132] 
[    8.716224] [dhd] Register interface [wlan0]  MAC: c0:f5:35:4f:8d:5e
[    8.716224] 
[    8.716392] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 3 -> mode 0
[    8.716400] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=40, TCPDATA_INFO_MAXNUM=40
[    8.716419] [dhd] [wlan0] wl_android_wifi_off :  g_wifi_on=1 force_off=1
[    8.716428] [dhd] dhd_bus_devreset: == Power OFF ==
[    8.716435] [dhd] dhdpcie_advertise_bus_cleanup: DB7 Not sent!!!
[    8.716447] [dhd] dhd_bus_stop: making DHD_BUS_DOWN
[    8.716592] [dhd] dhd_dpc_kill: tasklet disabled
[    8.721074] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN
[    8.721118] [dhd] dhd_bus_devreset:  WLAN OFF Done
[    8.721130] [dhd] wifi_platform_set_power = 0, delay: 0 msec
[    8.721138] [dhd] ======== PULL WL_REG_ON(-1) LOW! ========
[    8.721144] [WLAN_RFKILL]: rockchip_wifi_power: 0
[    8.721150] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized
[    8.721156] [dhd] [wlan0] wl_android_wifi_off : out
[    8.722402] [dhd] Register interface [wlan1]  MAC: c2:f5:35:4f:8d:5e
[    8.722402] 
[    8.722418] [dhd] wl_android_post_init: 0
[    8.722424] [dhd] dhdpcie_pci_probe : mutex is released.
[    8.722605] [dhd] _dhd_module_init: Exit err=0
Successfully init WiFi for AP6275P!
[    8.751862] [BT_RFKILL]: bt shut off power
xkbcommon: ERROR: couldn't find a Compose file for locale "en_US.UTF-8" (mapped to "en_US.UTF-8")
could not create XKB compose table for locale 'en_US.UTF-8'.  Disabiling compose
Successfully initialized wpa_supplicant
[    8.818453] [dhd] dhd_pri_open : no mutex held
[    8.818484] [dhd] dhd_pri_open : set mutex lock
[    8.818490] [dhd] [wlan0] dhd_open : Enter
[    8.818496] [dhd] Dongle Host Driver, version 101.10.591.46.22 (20231003-3)(a5ec15e)
[    8.818496] /home/jinhualong/new_disk_4t/wyb/RD-RK3588/repo_RK3588_Buildroot20240508/external/rkwifibt/drivers/bcmdhd compiled on Nov 27 2025 at 16:40:45
[    8.818496] 
[    8.818504] [dhd] dhd_open: ######### called for ifidx=0 #########
[    8.818513] [dhd] [wlan0] wl_android_wifi_on : in g_wifi_on=0
[    8.818518] [dhd] wifi_platform_set_power = 1, delay: 200 msec
[    8.818522] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ========
[    8.818526] [WLAN_RFKILL]: rockchip_wifi_power: 1
[    8.818530] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized
xkbcommon: ERROR: couldn't find a Compose file for locale "en_US.UTF-8" (mapped to "en_US.UTF-8")
could not create XKB compose table for locale 'en_US.UTF-8'.  Disabiling compose
[    9.024900] [dhd] wifi_platform_set_power = 1, sleep done: 200 msec
[    9.025035] [dhd] dhd_bus_devreset: == Power ON ==
[    9.025056] [dhd] dhd_bus_devreset: dhdpcie_bus_start_host_dev OK
[    9.025601] [dhd] ******** Perform FLR ********
[    9.025622] [dhd] config space 0x88 is 0x8080
[    9.025629] [dhd] ******** device not in FLR ********
[    9.025979] [dhd] ******** device force FLR only not set ********
[    9.025986] [dhd] Delay of 70 msec
[    9.101462] [dhd] read_config: reg=0x88 read val=0xb080
[    9.101651] [dhd] read_config: reg=0x88 read val=0xb080
[    9.101705] [dhd] read_config: reg=0x88 read val=0xb080
[    9.101871] [dhd] read_config: reg=0x88 read val=0xb080
[    9.101924] [dhd] read_config: reg=0x88 read val=0xb080
[    9.102091] [dhd] read_config: reg=0x88 read val=0xb080
[    9.102143] [dhd] read_config: reg=0x88 read val=0xb080
[    9.102310] [dhd] read_config: reg=0x88 read val=0xb080
[    9.102363] [dhd] read_config: reg=0x88 read val=0xb080
[    9.102529] [dhd] read_config: reg=0x88 read val=0x8080
[    9.102977] [dhd] ******** FLR Succedeed ********
[    9.103000] [dhd] Disable CTO
[    9.103752] [dhd] dhd_dump_pcie_slave_wrapper_regs pcie slave wrapper base not populated
[    9.103894] [dhd] DHD: dongle ram size is set to 1310720(orig 1310720) at 0x170000
[    9.103905] [dhd] dhdpcie_bar1_window_switch_enab: bar1_switch_enab=0 ramstart=0x170000 ramend=0x2affff bar1_size=0x400000
[    9.103936] [dhd] dhdpcie_request_irq: INTx enabled, irq=147
[    9.103986] [dhd] dhd_bus_download_firmware: firmware path=/vendor/etc/firmware/fw_bcmdhd.bin, nvram path=/vendor/etc/firmware/nvram.txt
[    9.104018] [dhd] dhd_conf_set_path_params : Final fw_path=/vendor/etc/firmware/fw_bcm43752a2_pcie_ag.bin
[    9.104026] [dhd] dhd_conf_set_path_params : Final nv_path=/vendor/etc/firmware/nvram_ap6275p.txt
[    9.104033] [dhd] dhd_conf_set_path_params : Final clm_path=/vendor/etc/firmware/clm_bcm43752a2_pcie_ag.blob
[    9.104042] [dhd] dhd_conf_set_path_params : Final conf_path=/vendor/etc/firmware/config.txt
[    9.104137] [dhd] dhd_os_open_image1: /vendor/etc/firmware/config.txt (240 bytes) open success
[    9.104191] [dhd] dhd_conf_read_pm_params : PM = 0
[    9.104203] [dhd] dhd_conf_read_pm_params : pm_in_suspend = 2
[    9.104216] [dhd] dhd_conf_read_others : keep_alive_period = 120000
[    9.104227] [dhd] dhd_conf_read_others : garp = 1
[    9.104237] [dhd] dhd_conf_read_pm_params : suspend_bcn_li_dtim = 10
[    9.104250] [dhd] dhd_conf_read_others : wl_preinit = pm2_sleep_ret=20
[    9.104263] [dhd] dhd_conf_read_pkt_filter : pkt_filter_del id = 100 102 103 104 105 107 
[    9.104295] [dhd] dhd_conf_read_pkt_filter : pkt_filter_add[0][] = 142 0 0 77 0xffffffffffffffffffffffffffffff 0x2F6465766963652F77616B6575702F
[    9.104307] [dhd] d2h_intr_method -> PCIE_INTX(0); d2h_intr_control -> D2H_INTMASK(0)
[    9.104520] [dhd] dhdpcie_download_code_file: dhd_tcm_test_enable 0, dhd_tcm_test_status 0
[    9.104528] [dhd] dhdpcie_download_code_file: download firmware /vendor/etc/firmware/fw_bcm43752a2_pcie_ag.bin
[    9.104551] [dhd] dhd_os_open_image1: /vendor/etc/firmware/fw_bcm43752a2_pcie_ag.bin (936074 bytes) open success
[    9.104610] [dhd] dhdpcie_download_code_file Using SINGLE image (size 936074)
[    9.199415] [dhd] dhd_os_open_image1: /vendor/etc/firmware/nvram_ap6275p.txt (7458 bytes) open success
[    9.199442] [dhd] dhdpcie_download_nvram: dhd_get_download_buffer len 7458
[    9.199447] [dhd] # AP6275P_NVRAM_V1.2_20210918A
[    9.199499] [dhd] dhdpcie_download_nvram: process_nvram_vars len 6036
[    9.218093] [dhd] dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded.
[    9.218103] [dhd] dhdpcie_bus_write_vars: New varsize is 6040, length token(nvram_csm)=0xfa1905e6
[    9.218552] [dhd] Download and compare of TLV 0xfeedc0de succeeded (size 128, addr 2ae7dc).
[    9.218646] [dhd] dhdpcie_bus_download_state: Took ARM out of Reset
[    9.218669] [dhd] dhd_bus_aer_config: Configure AER registers for EP
[    9.218694] [dhd] dhd_bus_aer_config: Configure AER registers for RC
[    9.255396] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host high!
[    9.308108] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host input!
[    9.308183] [BT_RFKILL]: ENABLE UART_RTS
[    9.311699] [dhd] dhdpcie_readshared: addr=0x20a584 nvram_csm=0xfa1905e6
[    9.311739] [dhd] ### Total time ARM OOR to Readshared pass took 93122 usec ###
[    9.311750] [dhd] dhdpcie_readshared: PCIe shared addr (0x0020a584) read took 90000 usec before dongle is ready
[    9.312140] [dhd] FW supports DAR ? N
[    9.312172] [dhd] H2D DMA WR INDX : array size 172 = 4 * 43
[    9.312178] [dhd] D2H DMA RD INDX : array size 16 = 4 * 4
[    9.312184] [dhd] D2H DMA WR INDX : array size 16 = 4 * 4
[    9.312189] [dhd] H2D DMA RD INDX : array size 172 = 4 * 43
[    9.312196] [dhd] dhdpcie_readshared: max H2D queues 40
[    9.312201] [dhd] FW supports debug buf dest ? N 
[    9.312205] [dhd] FW supports MD ring ? N
[    9.312349] [dhd] dhd_bus_init: Enabling bus->intr_enabled
[    9.312377] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 9, size 32896
[    9.312392] [dhd] dhd_prot_init:4138: h2d_max_txpost = 512
[    9.312397] [dhd] dhd_prot_init:4144: h2d_htput_max_txpost = 2048
[    9.312521] [dhd] dhd_prot_init: max_rxbufpost:511 rx_buf_burst:64 rx_bufpost_threshold:64
[    9.312529] [dhd] ENABLING DW:0
[    9.312535] [dhd] IDMA inited
[    9.312540] [dhd] IFRM not enabled in FW !!
[    9.312545] [dhd] DAR not enabled in FW !!
[    9.312549] [dhd] Enable hostcap: EXTD TXS in txcpl
[    9.312617] [dhd] dhd_prot_d2h_sync_init(): D2H sync mechanism is NONE 
[    9.312633] [dhd] dhd_bus_hostready : Read PCICMD Reg: 0x00100006
[    9.312654] [dhd] dhd_bus_hostready: Ring Hostready:1
[    9.312663] [dhd] iDMA not enabled yet,waiting 1 ms c=1 IDMAControl = 00000000
[    9.313784] [dhd] iDMA enabled PCIEControl = 00000001
[    9.315972] [dhd] trying to send create d2h info ring: id 46
[    9.315981] [dhd] dhd_send_d2h_ringcreate ringid: 3 idx: 46 max_h2d: 43
[    9.315989] [dhd] trying to send create h2d info ring id 45
[    9.316524] [dhd] dhd_prot_process_d2h_ring_create_complete ring create Response status = 0 ring 3, id 0xfffc
[    9.316558] [dhd] info buffer post after ring create
[    9.318499] [dhd] wlc_ver_major 12, wlc_ver_minor 1
[    9.320070] [dhd] dhd_sync_with_dongle: GET_REVINFO device 0x449d, vendor 0x14e4, chipnum 0xaae8
[    9.321375] [dhd] dhd_sync_with_dongle: RxBuf Post : 2048
[    9.321382] [dhd] dhd_sync_with_dongle: RxBuf Post Alloc : 2048
[    9.326446] [dhd] dhd_preinit_ioctls: preinit_status IOVAR not supported, use legacy preinit
[    9.326461] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 3
[    9.326468] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=40, TCPDATA_INFO_MAXNUM=40
[    9.330616] [dhd] dhd_legacy_preinit_ioctls: hostwake_oob enabled
[    9.332997] [dhd] dhd_legacy_preinit_ioctls: use firmware generated mac_address c0:f5:35:4f:8d:5e
[    9.333146] [dhd] dhd_os_open_image1: /vendor/etc/firmware/clm_bcm43752a2_pcie_ag.blob (30993 bytes) open success
[    9.335737] [dhd] dhd_check_current_clm_data: ----- This FW is not included CLM data -----
[    9.404115] [dhd] dhd_apply_default_clm: CLM download succeeded 
[    9.407018] [dhd] dhd_check_current_clm_data: ----- This FW is included CLM data -----
[    9.414892] [BT_RFKILL]: DISABLE UART_RTS
[    9.415044] [BT_RFKILL]: bt turn on power
[    9.415095] [BT_RFKILL]: Request irq for bt wakeup host
[    9.415161] [BT_RFKILL]: ** disable irq
[    9.417912] [dhd] Firmware up: op_mode=0x0005, MAC=c0:f5:35:4f:8d:5e
[    9.459196] [dhd] dhd_legacy_preinit_ioctls: event_log_max_sets: 26 ret: 0
[    9.464874] [dhd] arp_enable:1 arp_ol:0
[    9.464931] [dhd] dhd_conf_add_pkt_filter : 142 0 0 77 0xffffffffffffffffffffffffffffff 0x2F6465766963652F77616B6575702F
[    9.473431] [dhd]   Driver: 101.10.591.46.22 (20231003-3)
[    9.473431] [dhd]   Firmware: wl0: Jul 12 2022 18:54:54 version 18.35.387.23.146 (g412cc5ec) FWID 01-93c53be6
[    9.473431] [dhd]   CLM: 9.9.12_SS (2021-10-12 17:03:28) 
[    9.511508] Freeing drm_logo memory: 736K
[    9.512923] [dhd] dhd_ecounter_autoconfig Ecounter autoconfig in FW not supported
[    9.515986] [dhd] dhd_legacy_preinit_ioctls: d3_hostwake_delay IOVAR not present, proceed
[    9.518279] [dhd] dhd_update_interface_flow_info: ifindex:0 previous role:0 new role:0
[    9.518429] [dhd] dhd_rx_frame: net device is NOT registered. drop event packet
[    9.519049] [dhd] dhd_conf_same_country : country code = CN/0 is already configured
[    9.539510] [dhd] dhd_bus_devreset: WLAN Power On Done
[    9.539603] [dhd] [wlan0] wl_android_wifi_on : Success
[    9.576752] [dhd] dhd_update_interface_flow_info: ifindex:0 previous role:0 new role:0
[    9.576827] [dhd] dhd_rx_frame: net device is NOT registered. drop event packet
[    9.600600] [dhd] [wlan0] wl_cfg80211_up : Roam channel cache enabled
[    9.603752] [dhd] [wlan0] dhd_open : Exit ret=0
[    9.603802] [dhd] [wlan0] dhd_pri_open : tx queue started
[    9.603890] [dhd] [wlan0] custom_xps_map_set : Done. mapping cpu
[    9.603900] [dhd] dhd_pri_open : mutex is released.
[    9.632351] [dhd] P2P interface registered
nl80211: kernel reports: Registration to specific type not supported
[    9.660033] [dhd] P2P interface started
[    9.713408] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 0, bssidx: 0
###AMPAK FW Auto detection patch version = [v1.1 20161117]###
FW folder path = /lib/firmware
[    9.941046] of_dma_request_slave_channel: dma-names property of node '/serial@febc0000' missing or empty
proc_reset[    9.941084] dw-apb-uart febc0000.serial: failed to request DMA, use interrupt mode
chip id = BCM4362A2
FW path = /lib/firmware/BCM4362A2.hcd
send hci_download_minidriverproc_resetDone setting line discpline
N: [pulseaudio] bluez5-util.c: Could not find org.bluez.BatteryProviderManager1.RegisterBatteryProvider(), is bluetoothd started with experimental features enabled (-E flag)?
Successfully init BT for AP6275P!
Done
[   17.268729] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 1, bssidx: 0

root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# [   24.870012] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 2, bssidx: 0

root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# ifconfig
lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:42 errors:0 dropped:0 overruns:0 frame:0
          TX packets:42 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:2968 (2.8 KiB)  TX bytes:2968 (2.8 KiB)

wlan0     Link encap:Ethernet  HWaddr C0:F5:35:4F:8D:5E  
          inet6 addr: fe80::97f:f03b:3ce2:4d91/64 Scope:Link
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# [   32.463048] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 3, bssidx: 0
  
root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# ifconfig -a
enP4p65s0 Link encap:Ethernet  HWaddr 8A:C4:FE:A1:05:82  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:166 Base address:0x1000 

eth0      Link encap:Ethernet  HWaddr 16:43:B0:68:DA:A7  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:92 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:44 errors:0 dropped:0 overruns:0 frame:0
          TX packets:44 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:3088 (3.0 KiB)  TX bytes:3088 (3.0 KiB)

wlan0     Link encap:Ethernet  HWaddr C0:F5:35:4F:8D:5E  
          inet6 addr: fe80::97f:f03b:3ce2:4d91/64 Scope:Link
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan1     Link encap:Ethernet  HWaddr C2:F5:35:4F:8D:5E  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# [   40.020368] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 4, bssidx: 0
[   47.604376] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 5, bssidx: 0
[   55.175615] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 6, bssidx: 0
[   62.752052] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 7, bssidx: 0
[   70.341307] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 8, bssidx: 0
[   77.906375] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 9, bssidx: 0
[   85.524261] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 10, bssidx: 0
[   93.079702] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 11, bssidx: 0
[  100.648172] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 12, bssidx: 0
[  108.222756] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 13, bssidx: 0
[  115.822402] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 14, bssidx: 0
[  123.385810] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 15, bssidx: 0
[  130.952668] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 16, bssidx: 0
[  138.552527] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 17, bssidx: 0
[  146.120688] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 18, bssidx: 0
[  153.689212] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 19, bssidx: 0
[  161.244353] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 20, bssidx: 0
[  168.745836] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 21, bssidx: 0
[  176.314604] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 22, bssidx: 0
[  183.906800] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 23, bssidx: 0
[  191.486823] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 24, bssidx: 0
[  199.063834] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 25, bssidx: 0
[  206.643572] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 26, bssidx: 0
[  214.226459] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 27, bssidx: 0
[  221.789053] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 28, bssidx: 0
[  229.376590] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 29, bssidx: 0
[  236.939392] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 30, bssidx: 0
[  244.504208] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 31, bssidx: 0
[  252.099914] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 32, bssidx: 0
[  259.682431] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 33, bssidx: 0
[  267.269714] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 34, bssidx: 0
[  274.844738] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 35, bssidx: 0
[  282.408544] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 36, bssidx: 0

root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# [  289.723336] [dhd] Exit. P2P interface stopped
[  289.723497] [dhd] CFGP2P-ERROR) wl_cfgp2p_disable_discovery :  do nothing, not initialized
[  289.723935] [dhd] CFGP2P-ERROR) wl_cfgp2p_del_p2p_disc_if : P2P interface unregistered
[  289.728512] [dhd] [wlan0] dhd_pri_stop : tx queue stopped
[  289.728604] [dhd] [wlan0] dhd_stop : Enter
[  289.730389] [dhd] dhd_stop: ######### called for ifidx=0 #########
[  289.734294] [dhd] CFGP2P-ERROR) wl_cfgp2p_disable_discovery :  do nothing, not initialized
[  289.736388] [dhd] dhd_stop: making dhdpub up FALSE
[  289.736494] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 3 -> mode 0
[  289.736514] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=40, TCPDATA_INFO_MAXNUM=40
[  289.736727] [dhd] [wlan0] wl_android_wifi_off :  g_wifi_on=1 force_off=1
[  289.736752] [dhd] dhd_bus_devreset: == Power OFF ==
[  289.736772] [dhd] dhdpcie_advertise_bus_cleanup: DB7 Not sent!!!
[  289.736797] [dhd] dhd_bus_stop: making DHD_BUS_DOWN
[  289.736961] [dhd] dhd_dpc_kill: tasklet disabled
[  289.740701] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN
[  289.740715] [dhd] dhd_bus_devreset:  WLAN OFF Done
[  289.740725] [dhd] wifi_platform_set_power = 0, delay: 0 msec
[  289.740733] [dhd] ======== PULL WL_REG_ON(-1) LOW! ========
[  289.740741] [WLAN_RFKILL]: rockchip_wifi_power: 0
[  289.740748] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized
[  289.740755] [dhd] [wlan0] wl_android_wifi_off : out
[  289.742036] [dhd] [wlan0] dhd_stop : Exit

root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# [  321.699851] [dhd] dhd_pri_open : no mutex held
[  321.699894] [dhd] dhd_pri_open : set mutex lock
[  321.699902] [dhd] [wlan0] dhd_open : Enter
[  321.699910] [dhd] Dongle Host Driver, version 101.10.591.46.22 (20231003-3)(a5ec15e)
[  321.699910] /home/jinhualong/new_disk_4t/wyb/RD-RK3588/repo_RK3588_Buildroot20240508/external/rkwifibt/drivers/bcmdhd compiled on Nov 27 2025 at 16:40:45
[  321.699910] 
[  321.700315] [dhd] dhd_open: ######### called for ifidx=0 #########
[  321.700335] [dhd] [wlan0] wl_android_wifi_on : in g_wifi_on=0
[  321.700343] [dhd] wifi_platform_set_power = 1, delay: 200 msec
[  321.700349] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ========
[  321.700356] [WLAN_RFKILL]: rockchip_wifi_power: 1
[  321.700361] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized
[  321.904838] [dhd] wifi_platform_set_power = 1, sleep done: 200 msec
[  321.904883] [dhd] dhd_bus_devreset: == Power ON ==
[  321.904894] [dhd] dhd_bus_devreset: dhdpcie_bus_start_host_dev OK
[  321.905478] [dhd] ******** Perform FLR ********
[  321.905494] [dhd] config space 0x88 is 0x8080
[  321.905499] [dhd] ******** device not in FLR ********
[  321.905843] [dhd] ******** device force FLR only not set ********
[  321.905847] [dhd] Delay of 70 msec
[  321.981644] [dhd] read_config: reg=0x88 read val=0xb080
[  321.981886] [dhd] read_config: reg=0x88 read val=0xb080
[  321.982068] [dhd] read_config: reg=0x88 read val=0xb080
[  321.982248] [dhd] read_config: reg=0x88 read val=0xb080
[  321.982428] [dhd] read_config: reg=0x88 read val=0xb080
[  321.982610] [dhd] read_config: reg=0x88 read val=0xb080
[  321.982789] [dhd] read_config: reg=0x88 read val=0x8080
[  321.983489] [dhd] ******** FLR Succedeed ********
[  321.983510] [dhd] Disable CTO
[  321.984219] [dhd] dhd_dump_pcie_slave_wrapper_regs pcie slave wrapper base not populated
[  321.984354] [dhd] DHD: dongle ram size is set to 1310720(orig 1310720) at 0x170000
[  321.984363] [dhd] dhdpcie_bar1_window_switch_enab: bar1_switch_enab=0 ramstart=0x170000 ramend=0x2affff bar1_size=0x400000
[  321.984390] [dhd] dhdpcie_request_irq: INTx enabled, irq=147
[  321.984432] [dhd] dhd_bus_download_firmware: firmware path=/vendor/etc/firmware/fw_bcmdhd.bin, nvram path=/vendor/etc/firmware/nvram.txt
[  321.984459] [dhd] dhd_conf_set_path_params : Final fw_path=/vendor/etc/firmware/fw_bcm43752a2_pcie_ag.bin
[  321.984466] [dhd] dhd_conf_set_path_params : Final nv_path=/vendor/etc/firmware/nvram_ap6275p.txt
[  321.984472] [dhd] dhd_conf_set_path_params : Final clm_path=/vendor/etc/firmware/clm_bcm43752a2_pcie_ag.blob
[  321.984478] [dhd] dhd_conf_set_path_params : Final conf_path=/vendor/etc/firmware/config.txt
[  321.984585] [dhd] dhd_os_open_image1: /vendor/etc/firmware/config.txt (240 bytes) open success
[  321.984630] [dhd] dhd_conf_read_pm_params : PM = 0
[  321.984638] [dhd] dhd_conf_read_pm_params : pm_in_suspend = 2
[  321.984648] [dhd] dhd_conf_read_others : keep_alive_period = 120000
[  321.984656] [dhd] dhd_conf_read_others : garp = 1
[  321.984664] [dhd] dhd_conf_read_pm_params : suspend_bcn_li_dtim = 10
[  321.984674] [dhd] dhd_conf_read_others : wl_preinit = pm2_sleep_ret=20
[  321.984685] [dhd] dhd_conf_read_pkt_filter : pkt_filter_del id = 100 102 103 104 105 107 
[  321.984708] [dhd] dhd_conf_read_pkt_filter : pkt_filter_add[0][] = 142 0 0 77 0xffffffffffffffffffffffffffffff 0x2F6465766963652F77616B6575702F
[  321.984718] [dhd] d2h_intr_method -> PCIE_INTX(0); d2h_intr_control -> D2H_INTMASK(0)
[  321.984925] [dhd] dhdpcie_download_code_file: dhd_tcm_test_enable 0, dhd_tcm_test_status 0
[  321.984931] [dhd] dhdpcie_download_code_file: download firmware /vendor/etc/firmware/fw_bcm43752a2_pcie_ag.bin
[  321.984956] [dhd] dhd_os_open_image1: /vendor/etc/firmware/fw_bcm43752a2_pcie_ag.bin (936074 bytes) open success
[  321.984963] [dhd] dhdpcie_download_code_file Using SINGLE image (size 936074)
[  322.080057] [dhd] dhd_os_open_image1: /vendor/etc/firmware/nvram_ap6275p.txt (7458 bytes) open success
[  322.080080] [dhd] dhdpcie_download_nvram: dhd_get_download_buffer len 7458
[  322.080085] [dhd] # AP6275P_NVRAM_V1.2_20210918A
[  322.080128] [dhd] dhdpcie_download_nvram: process_nvram_vars len 6036
[  322.098634] [dhd] dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded.
[  322.098642] [dhd] dhdpcie_bus_write_vars: New varsize is 6040, length token(nvram_csm)=0xfa1905e6
[  322.099074] [dhd] Download and compare of TLV 0xfeedc0de succeeded (size 128, addr 2ae7dc).
[  322.099165] [dhd] dhdpcie_bus_download_state: Took ARM out of Reset
[  322.099187] [dhd] dhd_bus_aer_config: Configure AER registers for EP
[  322.099211] [dhd] dhd_bus_aer_config: Configure AER registers for RC
[  322.192205] [dhd] dhdpcie_readshared: addr=0x20a584 nvram_csm=0xfa1905e6
[  322.192245] [dhd] ### Total time ARM OOR to Readshared pass took 93109 usec ###
[  322.192256] [dhd] dhdpcie_readshared: PCIe shared addr (0x0020a584) read took 90000 usec before dongle is ready
[  322.192654] [dhd] FW supports DAR ? N
[  322.192814] [dhd] H2D DMA WR INDX : array size 172 = 4 * 43
[  322.192824] [dhd] D2H DMA RD INDX : array size 16 = 4 * 4
[  322.192834] [dhd] D2H DMA WR INDX : array size 16 = 4 * 4
[  322.192843] [dhd] H2D DMA RD INDX : array size 172 = 4 * 43
[  322.192853] [dhd] dhdpcie_readshared: max H2D queues 40
[  322.192862] [dhd] FW supports debug buf dest ? N 
[  322.192871] [dhd] FW supports MD ring ? N
[  322.193023] [dhd] dhd_bus_init: Enabling bus->intr_enabled
[  322.193072] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 9, size 32896
[  322.193098] [dhd] dhd_prot_init:4138: h2d_max_txpost = 512
[  322.193108] [dhd] dhd_prot_init:4144: h2d_htput_max_txpost = 2048
[  322.193236] [dhd] dhd_prot_init: max_rxbufpost:511 rx_buf_burst:64 rx_bufpost_threshold:64
[  322.193246] [dhd] ENABLING DW:0
[  322.193254] [dhd] IDMA inited
[  322.193261] [dhd] IFRM not enabled in FW !!
[  322.193268] [dhd] DAR not enabled in FW !!
[  322.193274] [dhd] Enable hostcap: EXTD TXS in txcpl
[  322.193307] [dhd] dhd_prot_d2h_sync_init(): D2H sync mechanism is NONE 
[  322.193327] [dhd] dhd_bus_hostready : Read PCICMD Reg: 0x00100006
[  322.193350] [dhd] dhd_bus_hostready: Ring Hostready:1
[  322.193361] [dhd] iDMA not enabled yet,waiting 1 ms c=1 IDMAControl = 00000000
[  322.194483] [dhd] iDMA enabled PCIEControl = 00000001
[  322.196241] [dhd] trying to send create d2h info ring: id 46
[  322.196251] [dhd] dhd_send_d2h_ringcreate ringid: 3 idx: 46 max_h2d: 43
[  322.196257] [dhd] trying to send create h2d info ring id 45
[  322.196523] [dhd] dhd_prot_process_d2h_ring_create_complete ring create Response status = 0 ring 3, id 0xfffc
[  322.196554] [dhd] info buffer post after ring create
[  322.198447] [dhd] wlc_ver_major 12, wlc_ver_minor 1
[  322.199931] [dhd] dhd_sync_with_dongle: GET_REVINFO device 0x449d, vendor 0x14e4, chipnum 0xaae8
[  322.201312] [dhd] dhd_sync_with_dongle: RxBuf Post : 2048
[  322.201319] [dhd] dhd_sync_with_dongle: RxBuf Post Alloc : 2048
[  322.206523] [dhd] dhd_preinit_ioctls: preinit_status IOVAR not supported, use legacy preinit
[  322.206546] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 3
[  322.206556] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=40, TCPDATA_INFO_MAXNUM=40
[  322.210811] [dhd] dhd_legacy_preinit_ioctls: hostwake_oob enabled
[  322.213284] [dhd] dhd_legacy_preinit_ioctls: use firmware generated mac_address c0:f5:35:4f:8d:5e
[  322.213425] [dhd] dhd_os_open_image1: /vendor/etc/firmware/clm_bcm43752a2_pcie_ag.blob (30993 bytes) open success
[  322.216179] [dhd] dhd_check_current_clm_data: ----- This FW is not included CLM data -----
[  322.275009] [dhd] dhd_apply_default_clm: CLM download succeeded 
[  322.277730] [dhd] dhd_check_current_clm_data: ----- This FW is included CLM data -----
[  322.289309] [dhd] Firmware up: op_mode=0x0005, MAC=c0:f5:35:4f:8d:5e
[  322.320347] [dhd] dhd_legacy_preinit_ioctls: event_log_max_sets: 26 ret: 0
[  322.340654] [dhd] arp_enable:1 arp_ol:0
[  322.340746] [dhd] dhd_conf_add_pkt_filter : 142 0 0 77 0xffffffffffffffffffffffffffffff 0x2F6465766963652F77616B6575702F
[  322.365678] [dhd]   Driver: 101.10.591.46.22 (20231003-3)
[  322.365678] [dhd]   Firmware: wl0: Jul 12 2022 18:54:54 version 18.35.387.23.146 (g412cc5ec) FWID 01-93c53be6
[  322.365678] [dhd]   CLM: 9.9.12_SS (2021-10-12 17:03:28) 
[  322.458940] [dhd] dhd_ecounter_autoconfig Ecounter autoconfig in FW not supported
[  322.465720] [dhd] dhd_legacy_preinit_ioctls: d3_hostwake_delay IOVAR not present, proceed
[  322.498192] [dhd] dhd_update_interface_flow_info: ifindex:0 previous role:0 new role:0
[  322.498344] [dhd] dhd_rx_frame: net device is NOT registered. drop event packet
[  322.502004] [dhd] dhd_conf_set_country : set country CN, revision 0
[  322.507283] [dhd] dhd_conf_set_country : Country code: CN (CN/0)
[  322.533151] [dhd] dhd_bus_devreset: WLAN Power On Done
[  322.533244] [dhd] [wlan0] wl_android_wifi_on : Success
[  322.569762] [dhd] dhd_update_interface_flow_info: ifindex:0 previous role:0 new role:0
[  322.569811] [dhd] dhd_rx_frame: net device is NOT registered. drop event packet
[  322.589971] [dhd] [wlan0] wl_cfg80211_up : Roam channel cache enabled
[  322.592363] [dhd] [wlan0] dhd_open : Exit ret=0
[  322.592432] [dhd] [wlan0] dhd_pri_open : tx queue started
[  322.592500] [dhd] [wlan0] custom_xps_map_set : Done. mapping cpu
[  322.592514] [dhd] dhd_pri_open : mutex is released.
[  322.610487] [dhd] P2P interface registered
[  322.650798] [dhd] P2P interface started
[  322.704348] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 37, bssidx: 0

root@rk3588-buildroot:/# [  325.282548] [dhd] [wlan0] wl_ext_set_chanspec : channel 5g-52(0xe03a 80MHz)
[  325.286028] [dhd] [wlan0] wl_conn_debug_info : Connecting with 6c:e8:74:da:32:41 ssid "GreatPeople -人间大炮", len (15), channel=5g-52(chan_cnt=1), sec=wpa2/psk/mfpn/aes, rssi=-46
[  325.377946] [dhd] dhd_update_interface_flow_info: ifindex:0 previous role:0 new role:0
[  325.378043] [dhd] dhd_update_multicilent_flow_rings: ifindex 0

root@rk3588-buildroot:/# [  325.517369] [dhd] [wlan0] wl_iw_event : Link UP with 6c:e8:74:da:32:41
[  325.517461] [dhd] [wlan0] wl_ext_iapsta_link : [S] Link UP with 6c:e8:74:da:32:41
[  325.519850] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
[  325.526157] [dhd] [wlan0] wl_bss_connect_done : Report connect result - connection succeeded
[  325.529060] [dhd] dhd_prot_flow_ring_create: Send Flow Create Req flow ID 37 for peer 6c:e8:74:da:32:41 prio 3 ifindex 0 items 512
[  325.529504] [dhd] dhd_prot_flow_ring_create_response_process: Flow Create Response status = 0 Flow 37
[  325.555222] [dhd] [wlan0] wl_add_keyext : key index (0) for 6c:e8:74:da:32:41
[  325.577419] [dhd] [wlan0] wl_cfg80211_set_suspend_bcn_li_dtim : bcn_li_dtim:0 lpas:0 bcn_to_dly:0
[  325.851094] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
[  325.851132] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
[  325.916627] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
[  326.022826] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
[  326.228447] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
[  326.537342] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
[  326.537381] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
[  326.750464] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
[  326.750502] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!

root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# ifconfig
lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:192 errors:0 dropped:0 overruns:0 frame:0
          TX packets:192 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:11968 (11.6 KiB)  TX bytes:11968 (11.6 KiB)

wlan0     Link encap:Ethernet  HWaddr C0:F5:35:4F:8D:5E  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:221 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:98141 (95.8 KiB)  TX bytes:361 (361.0 B)

root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# [  487.149292] [dhd] dhd_prot_flow_ring_create: Send Flow Create Req flow ID 41 for peer ff:ff:ff:ff:ff:ff prio 0 ifindex 0 items 2048
[  487.149769] [dhd] dhd_prot_flow_ring_create_response_process: Flow Create Response status = 0 Flow 41

root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# ifconfig
lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:204 errors:0 dropped:0 overruns:0 frame:0
          TX packets:204 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:12688 (12.3 KiB)  TX bytes:12688 (12.3 KiB)

wlan0     Link encap:Ethernet  HWaddr C0:F5:35:4F:8D:5E  
          inet addr:192.168.3.115  Bcast:192.168.3.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:315 errors:0 dropped:0 overruns:0 frame:0
          TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:146187 (142.7 KiB)  TX bytes:1531 (1.4 KiB)

root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# iperf
iperf   iperf3  
root@rk3588-buildroot:/# iperf^C
root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# 
root@rk3588-buildroot:/# 

[END] 2025/11/27 16:57:53